Herunterladen Inhalt Inhalt Diese Seite drucken
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 59
3. Loosen the lower knobs.
4. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 24)
5. Fold the handle forward. (Fig. 25)
To set the product in operation position
1. Lift the handlebar until the lower handle locks in
operation position. (Fig. 26)
2. Move the knobs up in the direction of the handle until
they stop and you hear a click.
3. Tighten the knobs fully. (Fig. 27)
4. Lift the top part of the handlebar.
Introduction
WARNING: Before you operate the product,
you must read and understand the safety
chapter.
Husqvarna Connect
Husqvarna Connect is a free app for your mobile device.
The Husqvarna Connect app gives extended functions
for your Husqvarna product:
Extended product information.
Information about, and help with, product parts and
servicing.
To start to use Husqvarna Connect
1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect
app to connect and register the product.
Before you operate the product
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. Examine the cutting equipment to make sure that it
is correctly attached and adjusted. See
the cutting equipment on page 13 .
3. Fill the fuel tank. See
4. Fill the oil tank and do a check of the oil level. See
To do a check of the oil level on page 14 .
To fill fuel
If available, use gasoline with a low emission grade/
alkylate fuel. If gasoline with a low emission grade/
alkylate fuel is not available, use good quality unleaded
gasoline or leaded gasoline with octane number not less
than 91.
1562 - 001 - 21.10.2020
To examine
To fill fuel on page 11 .
5. Tighten the knobs fully. (Fig. 28)
To assemble the grass catcher
1. Put the top part of the grass catcher onto the lower
part of the grass catcher. (Fig. 29)
2. Attach the grass catcher frame with the clips. (Fig.
30)
3. Lift the rear cover.
4. Attach the hooks on the grass catcher to the top
edge of the chassis. (Fig. 31)
5. Put the lower part of the grass catcher into the grass
discharge channel.

Operation

CAUTION: Do not use gasoline with an
octane number less than 91 RON. This can
cause damage to the product.
CAUTION: Replace the fuel filter yearly or
more frequently if it is necessary. A new fuel
filter is available at your Husqvarna dealer.
CAUTION: Always stop the engine before
you fill fuel.
CAUTION: Do not use pressurized starting
fluids.
1. Open the fuel tank cap slowly to release the
pressure.
2. Fill slowly with a fuel can. If you spill fuel, remove it
with a cloth and let remaining fuel dry off. (Fig. 32)
3. Clean the area around the fuel tank cap.
4. Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
5. Move the product a minimum of 3 m / 10 ft from the
position where you filled the tank before a start.
To set the cutting height
1. Move the cutting height lever rearward to increase
the cutting height.
2. Move the cutting height lever forward to decrease
the cutting height. (Fig. 33)
CAUTION: Do not set the cutting height too
low. The blades can hit the ground if the
surface of the lawn is not level.
11

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Lc 140sp

Inhaltsverzeichnis