Transport; Cleaning, Maintenance, Storage And Ordering Of Spare Parts; Service Information; Ordering Replacement Parts - Scheppach Parkside PDS 120 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

Please provide the following information in the event of any
enquiries:
• Type of current for the motor
• Machine data - type plate

12. Transport

• Transport the electric tool by lifting it on the recesses pro-
vided for this on the frame and the engine cover.
• Never use the protective devices for handling or transport.
• Make sure that the exposed part of the saw blade is covered
during transport, e. g. by the protective device.
13. Cleaning, maintenance, storage and
ordering of spare parts
WARNING
Always switch the machine off and remove the mains plug prior
to all maintenance and cleaning work.
13.1 Cleaning
Keep all safety devices, air vents and the motor housing free of
dirt and dust as far as possible. We recommend that you clean
the equipment immediately after you use it.
13.1.1 Exterior cleaning
• Clean the equipment regularly with a damp cloth and some
soft soap.
• Do not use cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
• Ensure that no water can get into the interior of the equip-
ment.
13.1.2 Interior cleaning (fig. 15)
1. Open the storage box (9).
2. Remove the screw (35).
3. Loosen the screw (34).
4. Remove the cover (8).
5. Blow out the device interior with low-pressure com-
pressed air.
6. Attach the cover again (8).
7. Fasten the screw (34).
8. Insert the screw (35) again and tighten it.
9. Close the storage box (9).
13.2 Servicing
13.2.1 Bearings (fig. 1/pos. 10)
Lubricate the bearing points (10) of the deflection rollers after
approx. 25-30 operating hours at the latest using high-quality
machine grease.
13.2.2 Carbon brushes
In case of excessive sparking, have the carbon brushes checked
only by a qualified electrician.
IMPORTANT
The carbon brushes should not be replaced by anyone but a
qualified electrician.
10 GB/IE
13.2.3 Mains cable
If the mains cable is pulled out, cut, or damaged in some other
form, then it should be replaced immediately.
13.2.4 Replacing the fine-wire fuse (fig. 16)
If the fine-wire fuse (36) is defective, it must be replaced with
a fine-wire fuse of the same type 5 A/250 V (ø 5 x 20 mm).
WARNING
Do not bypass the fine-wire fuse (36)! Do not use fuses of any
other type! This can lead to damage to the device.

13.3 Service information

Please note that the following parts of this product are sub-
ject to normal or natural wear and that the following parts are
therefore also required for use as consumables.
Wear parts*: Carbon brushes, saw blade, table insert
* Not necessarily included in the scope of delivery!

13.4 Ordering replacement parts

Please provide the following information when ordering re-
placement parts (via the service-hotline):
• Device type
• Device article number (see packaging or instruction manual)

14. Storage

Store the equipment and accessories out of children's reach in
a dark and dry place at above freezing temperature. The ideal
storage temperature is between 5 and 30 °C. Store the electric
tool in its original packaging.

15. Disposal and recycling

The equipment is supplied in packaging to prevent it from being
damaged in transit. The raw materials in this packaging can be
reused or recycled.
The equipment and its accessories are made of various types
of material, such as metal and plastic. Defective components
must be disposed of as special waste. Ask your dealer or your
local council.
The packaging is wholly composed of environment-
ally-friendly materials that can be disposed of at a
local recycling centre.
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
electrical devices.