Assembly - Scheppach Parkside PDS 120 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

• Before you actuate the On/Off switch, make sure that the
saw blade is correctly fitted and that the equipment's moving
parts run smoothly.
• Check that the voltage on the rating plate is the same as
your supply voltage before you connect the equipment to
the power supply.
• Only ever connect the equipment to a properly installed
shock-proof socket which is protected by a 10 A fuse as a
minimum.
8.3 Installing the fretsaw on a workbench
Required for installing:
Included in the scope of delivery:
• M8 hexagonal bolt (4x)
• M8 hexagonal nut (4x)
• Washer Ø 8,4 mm (8x)
• Drill template
The length of the screws to be used varies, depending on the
thickness of the table top.
WARNING
Danger of injury! Disconnect the mains plug on the scroll saw
before all assembly work.
1. The length of the screws to be used varies, depending on
the thickness of the table top.
2. Mark the drill holes (see fig. 5.2) using the attached drill
template.
3. Drill 4 holes with a diameter of 8 mm into the work table.
4. Screw the scroll saw onto the workbench with the hex-
agonal bolt (E) through the assembly points (fig. 3 pos.
19) in the following sequence (fig. 5.1):
D Hexagonal nut
C Washer
A Fretsaw
B Work table
C Washer
E Hexagonal bolt
5. Tighten the hexagonal nut (D) first.

9. Assembly

WARNING
Danger of injury! Disconnect the mains plug on the scroll saw
before all assembly work.
9.1 Fitting / Replacing the saw blade (fig. 1, 8-11)
IMPORTANT
To avoid injuries attributed to inadvertent startup: Before remov-
ing or replacing the saw blade, always press "0" and remove
the mains plug from the socket.
9.1.1 Removing/inserting the table insert
1. Loosen the knurled screw (3).
2. Set the saw blade guard (5) all the way up to the top
position.
3. Reach under the saw table (6) and press the table insert
(26) upwards.
4. It is now possible to remove the table insert (26).
Pay attention to the position of the sawing gap when inserting
the table insert (26). The table insert (26) must be inserted as
shown in fig. 8. Otherwise the machine can be damaged dur-
ing mitre cuts.
9.1.2 Removing the saw blade without pins (op-
tional)
1. To remove the saw blade (22) , lift the table insert (26)
upwards. (see 9.1.1)
2. First, release the tension by flipping the tension lever (11)
upwards. The tension can be reduced, if necessary, by
turning the tension lever (11) counterclockwise.
3. Press the support (12) down lightly (see fig. 9).
4. Then loosen the upper saw blade clamping screw (28).
5. Now hold the saw blade firmly, otherwise it will fall into
the interior of the machine.
6. Loosen the lower saw blade clamping screw (29) with
the Allen key (23).
7. Remove the saw blade of the machine upwards.
9.1.3 Inserting the saw blade without pins
(optional)
The teeth of the saw blade must always point downwards.
1. First, secure the saw blade (22) in the lower saw blade
mounting (30). To secure the saw blade (22), tighten the
lower saw blade clamping screw (29) using the Allen
key (23).
2. Press the support (12) down lightly. Fasten the other end
of the saw blade (22) in the top saw blade holder (27)
(see fig. 9).
3. Fix the saw blade (22) with the upper blade clamping
screw (28) (see fig. 10).
4. Tighten the saw blade (22) with the clamping lever
(11), by pressing it down again. Check the tension of
the saw blade (22). If the tension is insufficient, it can be
increased by turning the lever clockwise. First release the
clamping lever (11).
5. Put the table insert (26) back. (see 9.1.1)
9.1.4 Removing the saw blade with pins
1. To remove the saw blade (22), lift the table insert (26)
upwards. (see 9.1.1)
2. First, release the tension by flipping the tension lever (11)
upwards. Continue reducing the tension by turning clock-
wise as required.
3. Hold the saw blade firmly and press the arm (12) down
slightly (see fig. 9).
4. Pull the saw blade from the upper and lower saw blade
mounting (27/30).
9.1.5 Inserting the saw blade with pins
The teeth of the saw blade must always point downwards.
1. Insert one end of the saw blade (22) through the drilled
hole in the table. Insert the pins of the saw blade (22) into
the corresponding recesses of the top and bottom saw
blade holder (27/30).
2. First insert the saw blade (22), in the lower blade holder (30).
3. Press the support (12) down lightly (see fig. 9). Insert the
saw blade (22) into the upper saw blade holder (27).
4. Check the position of the saw blade pins in the saw blade
mountings (27/30).
GB/IE 7