Cardin Elettronica BL-Serie Bedienungsanleitung Seite 17

Terminal board connections
7 CMN common for all inputs and outputs
ELS electric lock output (fed continuously) 2 Vdc - 5 W.
8
9-10 LC-CH2 potential free contact for the activation of the courtesy light
(separate power supply Vmax = 30 Vac/dc: Imax = A) or the second
radio channel. Selection is carried out using jumper "J5".
CMN common for all inputs and outputs
11
12 LP 24 Vdc 25 W output for warning lights
intermittent activation (50%), 2,5 W continuous activation
LS 24 Vdc 3 W output for an indicator light
13
14 CMN common for all inputs and outputs
15 30 Vdc controlled output, powering external loads
16 CMN common for all inputs and outputs
30 Vdc output, powering external loads
17
18 CMN common for all inputs and outputs.
19 TA (NO contact) opening button input
20 TC (NO contact) closing button input
TAL (NO contact) limited opening button input
21
22 TD (NO contact) dynamic button input
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
23 CMN common for all inputs and outputs
TB (NC contact) stop button input (The opening of this contact inter-
24
rupts the cycle until a new movement command is given).
25 FTCS (NC contact) Safety and control devices in input. (stop photo-
electric cells). The opening of this contact will block all movement, until
the obstruction has been removed and the pause time has elapsed, due
to the safety device cutting in, the door will then continue moving in the
closing direction (only with automatic reclosing enabled).
26 FTCI (NC contact) Safety and control devices in input (photocells invert
the travel direction when an obstruction is detected). Opening this contact
will provoke a travel direction inversion during closure due to the cutting
in of the safety device.
27 EMRG2 (NO) emergency manoeuvre input 2
EMRG (NO) emergency manoeuvre input 1
28
29 CMN common for the emergency buttons
30 Inner conductor for radio receiver antenna (if an external antenna is
fitted use a coaxial type cable RG58 with an impedance of 50Ω).
J1
10
Collegamento motori/encoder a 4 fili
Connecting motor/4-wire encoder
Branchement moteur/encodeur à 4 fils
Anschluss der Motor/Encoder mit 4 Drähten
Conexionado motores/encoder de 4 conductores
B Signal buzzer "via radio" mode
CSER Serial connection (only for diagnostics)
D
Six-segment LED display
DS Selection dip-switch
F 0A blade fuse
F2 0A blade fuse
F3 4A blade fuse
F4 4A blade fuse
F5 4A blade fuse
J Battery connection
Drawing number :
Product Code :
Downloaded from www.Manualslib.com
()
10 4A
F2 F4
F3
L3
J2
F1
COLORE COLOUR CODE COLORATION
CABLAGGI CODE DES CÂBLAGES
Bl Blu Blue Bleu
Gr Verde Green Vert
Gy Grigio Grey Gris
Yw Giallo Yellow Jaune
KABELFARBEN COLORACIÓN
CABLEADOS
Bl Blau Azul
Gr Grün Verde
Gy Grau Gris
Yw Gelb Amarillo
ENCODER 2
ENCODER 1
M1 M2
Bl Gr
Bl Gr Gy Yw
1 2 3 4 5 6 1 2 3 4
(motor power protection)
(5)
(motor protection during battery operation)
(5)
(24V circuit protection)
(5)
(24V circuit protection during battery operation)
(5)
(electric lock protection)
(5)
Description :
DC0388
CC242ESBBS
manuals search engine
31 Outer conductor for radio receiver antenna
Note The total of the 2 external device outputs must not exceed 0 W.
()
ALL UNUSED NC CONTACTS MUST BE JUMPED and consequently the
security device test must also be deactivated (FTCI , FTCS - Dip 7 and Dip
8 "OFF") . If you want to activate the FTCI, FTCS test both the transmission
and receiver parts of the security devices must be connected to the binding
post marked "CTRL 30 Vdc". If the test is active there will be a 1 second
delay between the command transmission and movement of the gate/s.
Switch on the power and make sure that the indicator LEDs are in the fol-
lowing condition.
()
- L Power on
- L2 Battery charging
- L3 Wrong battery connection
- L4 Transmitter code programming indicator
- L5 Indicator for the blocking button "TB"
- L6 Indicator for the inverting photoelectric cells "FTCI"
- L7 Indicator for the stop photoelectric cells "FTCS"
- L8 Indicator for the opening button "TA"
- L9 Indicator for the closing button "TC"
- L0 Indicator for the limited opening button "TAL"
- L Indicator for the sequential command "TD/CH"
Note : This LED is "ON" when the battery is charging.
(2)
Note : If this LED is "ON" invert the battery power cables immediately.
(3)
Note : Check that the activation of the safety devices switches the cor-
(4)
responding LEDs off.
If the green power on LED "L" doesn't light up check the condition of the
fuses and the power cable connection at the transformer primary.
If one or more of the safety LEDs do not light up check the contacts of the
relative security devices and check that the unused safety device contacts
have been bridged.
R1
L2
MM
L1
J3 J4
DS1
TD
RA
PLP
LP
LS
FTCI
TFTI
TFTS
SAP
ELS
F5
Gy Yw
LC/CH2
5 6 7 8 9 10 11 12 13 14
J2 Transformer secondary protection
J3 Enable transmitter memorisation via radio
J4
Radio channel selection
J5
Binding posts 9, 10 selection (courtesy light/CH2 via radio)
MM
Transmitter code memory module
P
Programming button (PROG)
P2
Transmitter code memorization button (MEMO)
P3 Transmitter code cancellation button (DEL)
R Radio frequency module, 433 MHz for S449 transmitters
Note : These are automotive type blade fuses (max. voltage 58 V)
(5)
Collegamenti scheda base
7
CENTRALINA 2 MOTORI CC CON ENCODER
CS 1218 DC0355
B1
L5 L8
L10
L6
D1
L9
L7 L11
P2
L4
J5
P3
1 2
1 2
3
3
Pos.1 Pos.2
15 16 17 18 19 20 21 22 23 24
ON
OFF
(2)
OFF
(3)
OFF
ON
(4)
ON
(4)
ON
(4)
OFF
OFF
OFF
OFF
P1
CSER
CMN
EMRG 1
EMRG 2
25 26