YATO YT-85715 Bedienungsanleitung Seite 14

GB
similar way to the inlet orifi ce: slide it in and turn to block. In such case, one of inlet orifi ces should be plugged.
The cover of vacuum cleaner has been fi tted with handles allowing temporary fi xing of accessories for the time of work or storage
of the vacuum cleaner. It is possible to attach extension pipes and suction nozzle in handles.
Working with vacuum cleaner
NOTE! It is forbidden to work with a vacuum cleaner with hot ashes. The temperature of trash sucked by vacuum cleaner cannot
exceed 40 degrees centigrade.
Make sure that all preparatory operations have been carried out in a correct way.
Make sure that the vacuum cleaner switch remains in the off position - „O".
Plug the power cord into the mains socket, and then turn the switch to the on position - "I" (XIII).
The vacuum cleaner has been fi tted with a knob to adjust the suction force of the vacuum cleaner (XIV). It is recommended to
set the lowest required suction force for a given work. Turning the knob towards the „MAX" symbol increases the vacuum cleaner
suction force, turning the knob towards the „MIN" symbol reduces the vacuum cleaner suction force.
To stop the vacuum cleaner, turn the switch to the off position - „O"
The brush is fi tted with a lever that slides off the bristles. The bristles should be slid off when cleaning smooth, hard surfaces. It is
recommended to clean carpet fl oorings and carpets with hidden bristles.
After the work is fi nished, switch off the vacuum cleaner with a switch, and then disconnect the power plug from the mains socket.
Proceed to operations that [reserve the vacuum cleaner.
If a drop in performance is observed during dry cleaning with the upper container, this may indicate a clogged fi lter. It is possible
to try cleaning the fi lter by using the function reversing the direction of suction. Press and hold the reverse suction button (XV) for
a few seconds. Repeat this procedure several times. If a drop in performance is persistent, stop the work, disconnect the power
cord plug from the mains socket and clean the fi lter manually or replace it with a new one.
Built-in electrical socket
The vacuum cleaner features a built-in electrical socket, which is used to supply the power tools belonging to I and II class of
electrical insulation.
This allows for easier use of the vacuum cleaner in the form of system of extraction of dust generated during the work. Voltage
appears in the socket when the plug of power cord supplying the vacuum cleaner is connected to the mains socket. Therefore,
before connecting the vacuum cleaner to power supply and the power tool to the vacuum cleaner socket, make sure that switches
of both devices remain in the off position.
After connecting the vacuum cleaner to the outlet of power tool's dust extraction (a suitable adapter may be needed for this, that is
not delivered with the vacuum cleaner) and the power tool plug to the vacuum cleaner socket, the vacuum cleaner may be started
by turning the switch to the "I" position, the vacuum cleaner will start working regardless of the operation of power tool and it will
continue to work until the switch is turned to the "O" position.
An automatic mode is the recommended operating mode. To this end, after connecting the vacuum cleaner to the outlet of power
tool's dust extraction, and the power tool plug to the vacuum cleaner socket, turn the switch to the "II" position. The vacuum clean-
er will switch on automatically after a short time from the start-up of power tool and will also switch off automatically after a short
time from switching off the power tool.
Regardless of the selected mode of operation, after the work is fi nished, switch off the vacuum cleaner by turning the switch to the
"O" position, and then disconnect the vacuum cleaner plug from the mains socket, unplug the power tool from the vacuum cleaner
socket and proceed with maintenance operations.
Emptying the container of vacuum cleaner
After the dry vacuum cleaning is fi nished, dismantle the cover and check the container's fi lling level. Due to container capacity, it
is recommended to empty it after each use. It will be easier than emptying a full container.
After the wet vacuum cleaning is fi nished, dismantle the cover of vacuum cleaner. Impurities remaining in container can be
removed by tilting the container. After having it emptied, clean the container with a water jet and then allow it to dry thoroughly.
Vacuum cleaner maintenance
Note! Before proceeding with any maintenance operations, make sure that the power cord plug has been disconnected from the
mains socket.
Each time, when using the vacuum cleaner, please check the container, cover gasket and air fi lters as described in point: "Prepa-
ration to work".
Clean the vacuum cleaner from the outside using a jet of compressed air at a pressure not more than 0.3 MPa. In particular, pay
attention to patency of vents, both inlet and outlet. If it is necessary, clean it using a jet of compressed air at a pressure not more
O R I G I N A L I N S T R U C T I O N S
14