Die Set User Manual - Canon Multi Function Professional Puncher – A1 Bedienungsanleitung

8. DIE SET USER MANUAL

The die sets for the Professional Puncher are intended to work with
multiple paper sizes and sheet feed directions. In order to
accommodate different sheet sizes this die set must be configured to
the correct number of punching pins and the die stop must be set to
the proper position. The die label contains information on the common
paper punching sizes, for the uncommon sizes please refer to
Table 8.1.
Glossary
LEF- Long Edge Feed- Indicates that the paper is being fed through
the machine so that the longer side of the sheet will be punched.
SEF- Short Edge Feed- Indicates that the paper is being fed through
the machine so that the shorter side of the sheet will be punched.
Statement Paper- 8.5" X 5.5"
Legal Paper- 8.5" X 14"
Ledger Paper- 11" X 17"
Pin Numbering
Die punching pins are numbered sequentially starting from the handle
end. Figure 8.1 shows a 47 hole coil die as an example. All square and
round hole die sets follow the same pin numbering format.
Pin #47
Figure 8.1 Coil Die Set Pin Numbering
Figure 8.2 Pressure Bar Removal
Pin Removal
Wire
Coil
2:1
Rnd
Rnd
US Paper Sizes
Canon Part Number
LTR LEF 2, 47 1, 23
LTR SEF 7, 42 NONE
STATEMENT LEF 7, 42 NONE
LEGAL SEF 7, 42 NONE
LEDGER SEF 2, 47 1, 23
9" x 12" LEF 1, 2, 47 1, 23
9" x 12" SEF 6, 7, 42, 43 3, 21
12" x 18" SEF 1, 2, 47 1, 23
Wire
Coil
2:1
Rnd
Rnd
ISO Paper Sizes
Canon Part Number
A4 LEF NONE NONE
A4 SEF 7, 41 4, 21
A5 LEF 7, 41 4, 21
A3 SEF NONE NONE
SRA4 LEF NONE NONE
SRA4 SEF 6, 7, 42, 41 4, 21
SRA3 SEF NONE NONE
*For CombBind 20H Configuration Pull Pin Number 1
The above chart shows the information on which pins need to be removed to correctly punch each sheet size and configuration that the Professional
Puncher can accept. For standard offering dies not found in the chart no pin adjustment is necessary.
Multi Function Professional Puncher – A1
Pin #1
Quarter Turn
Fastener
Wire 3/5/7
3 Hole
3:1 Hole
8mm
Rnd 8mm
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
5, 31 N/A N/A
5, 31 N/A N/A
1, 34 NONE 3H/5H/7H
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
1, 34 NONE 3H/5H/7H
Wire 3/5/7
3 Hole
3:1 Hole
8mm
Rnd 8mm
NONE N/A N/A
5, 30 N/A N/A
5, 30 N/A N/A
NONE N/A N/A
NONE N/A N/A
4, 5, 30, 31 N/A N/A
NONE N/A N/A
Table 8.1 Pin Removal Guide
To remove punch pins from the Professional Puncher first turn the two
Quarter Turn Fasteners CCW direction to release the pressure bar.
Remove the pressure bar and set aside.
Note: Lubricating oil may be present on the die pins, wear gloves if
needed.
Lift up and remove the desired pins according to Table 8.1. Store pins
in the pin storage tray inside front door of machine making sure pins
cannot be dropped, damaged or lost while removed.
Replace the pressure bar by lining up dowel pin holes with exposed
dowel pins. Hold pressure bar so that it is seats completely over dowel
pins and then rotate Quarter Turn Fasteners clockwise until a click is
felt to lock pressure bar in position. The pressure bar can be locked
only if the orientation is correct, it cannot be locked in any other
orientation.
Important!
Before reinserting, clean the punch pin to remove any dust or foreign
substances.
Make sure pressure bar is attached and both Quarter Turn Fasteners
are in the locked position prior to inserting the die set into the machine
or serious damage can occur to both the machine and die set.
2/4 2/4
Hole Hole Hole
8mm 6.5mm SCAN
Pin Numbers to Remove Based On Paper Size or Orientation
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
2/4 2/4
Hole Hole Hole
8mm 6.5mm SCAN
Pin Numbers to Remove Based On Paper Size or Orientation
2H/4H 2H/4H NONE
2H 2H NONE
2H 2H NONE
2H/4H 2H/4H NONE
2H/4H 2H/4H NONE
N/A N/A NONE
2H/4H 2H/4H NONE
Figure 8.3 Pressure Bar
Figure 8.4 Pin Removal
Dowel Pin Holes
Figure 8.5 Replace Pressure Bar
2/4 VeloBind VeloBind
11 Hole 12 Hole CombBind
LTR A4
NONE N/A 1, 21
N/A N/A NONE
N/A N/A NONE
N/A N/A NONE
NONE N/A 1, 21
NONE N/A 1, 21
N/A N/A 3, 19
NONE N/A 1, 21
2/4 VeloBind VeloBind
11 Hole 12 Hole CombBind
LTR A4
N/A NONE NONE
N/A N/A 4, 19
N/A N/A 4,19
N/A NONE NONE
N/A NONE NONE
N/A N/A 4, 19
N/A NONE NONE
EN
Wire Wire
2:1 3:1
Sq Sq
1, 23 1,34
NONE 5,31
NONE 5,31
NONE 5,31
1, 23 1, 34
1, 23 1, 34
3, 21 5, 31
1, 23 1, 34
Wire Wire
2:1 3:1
Sq Sq
NONE NONE
4, 21 5, 30
4, 21 5, 30
NONE NONE
NONE NONE
4, 21 4, 5, 30, 31
NONE NONE
11