Fein MultiMaster FMM350Q Originalbetriebsanleitung Seite 19

OBJ_BUCH-0000000135-002.book Page 19 Wednesday, January 22, 2014 3:20 PM
The declared vibration emission level represents the
main applications of the tool. However, if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Emission values for vibration
Vibration
Classification of FEIN application
tools according to vibration class
VC0
VC1
VC2
VC3
VC4
VC5
a
K
* These values are based on a work cycle consisting of no-load
and full-load operation of the same duration.
For information on the vibration class assigned to the application
tool, please see the enclosed data sheet 3 41 30 421 06 0.
Operating Instructions.
Do not use accessories not specifically intended and
recommended for this power tool by FEIN. The use of non-
original FEIN accessories can lead to overheating of the
power tool and destroy it.
Guide the power tool toward the work piece only
when switched on.
The application tool can be offset in 45° steps and fas-
tened in the most favourable working position.
Changing the tool (see page 5).
Firmly press in the fastening element to the stop.
Then lock the clamping lever.
Protect your hand and fingers against bruising when
locking the clamping lever. The clamping lever
snaps back vigorously by means of spring force.
Notes on sanding.
Press the power tool with the sanding sheet briefly and
firmly against a flat surface and briefly switch the power
tool on. This provides for good adhesion and prevents
premature wear.
When only one tip or corner of the sanding sheet is
worn, it can be removed again and reattached turned by
120°.
Work with the entire surface of the sanding plate, not
only with the tip.
When sanding with the triangle sanding plate, select a
high oscillating frequency (electronics level 4 – 6); when
sanding with the round sanding plate, select a moderate
oscillating frequency (max. electronics level 4).
Sand with continuous motion applying moderate pres-
sure. Applying excessive pressure does not increase the
rate of removal, it only wears off the sanding sheet faster.
Notes on profile sanding.
Select a medium oscillating frequency.
Notes on sawing.
Select a high oscillating frequency. Round saw blades can
be released and clamped offset again, to allow for uni-
form wearing off.
Notes on scraping.
Select a moderate to high oscillating frequency.
Repair and customer service.
When working metal under extreme operat-
Weighted
ing conditions, it is possible for conductive
acceleration*
dust to settle in the interior of the power tool.
2
< 2.5 m/s
The total insulation of the power tool can be impaired.
2
< 5 m/s
Blow out the interior of the power tool via the ventila-
2
tion slots frequently with dry and oil-free compressed air,
< 7 m/s
and connect a residual current device (RCD) on the line
2
< 10 m/s
side.
2
< 15 m/s
If the supply cord of this power tool is damaged, it must
2
> 15 m/s
be replaced by a specially prepared cord available through
2
the FEIN customer service centre.
3 m/s
For storage of the power tool, remove the application
tool, shut the clamping lever, and then press in the fasten-
ing element.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
Fastening element, clamping bolt, application tools
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. FEIN GmbH, C-DB_IA,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
en
19