Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
Spare Soldering Iron for 1553055, 1620655
Item No. 1953677
Intended Use
This is a spare soldering iron that can be used with BN1553055 and BN1620655.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Soldering iron
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health, e.g. due to an
electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important information in
these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General Information
• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other products which are connected
to the product.
• Consult an expert when in doubt about the operation, safety or connection of the product.
• Maintenance, modifications and repairs must only be completed by a technician or an
authorised repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) Operation
• Never use the soldering iron to heat up liquids.
• Never solder live electrical components or parts. Always switch off the power before-hand.
• Do not cover or fasten any items to the soldering iron. Otherwise there is a risk of fire.
• Touching or soldering capacitors (or similar components) or leads/cables that are connected
to capacitors may cause a fatal electric shock! Capacitors may stay charged for several hours
after you switch off the power supply!
• Ensure that there is sufficient lighting.
• Ensure proper ventilation during soldering. Solder and flux vapours can be harmful to your
health.
• Wash your hands thoroughly after working with solder. This is particularly important when
using lead-based solder.
• Do not put soldering alloys into your mouth. Do not eat or drink during soldering.
• Wear suitable protective clothing and safety goggles when soldering. Liquid/splashing solder
may cause serious burns or eye damage.
• Never use soldering flux, acid or similar aids when soldering. Such materials result in poor
soldering joints. They may also damage the tip of the soldering iron.
• When using the soldering iron, do not touch any other part of the soldering iron apart from the
handle. Otherwise there is a danger of burning!
• Always solder on non-flammable surfaces. Protect other materials nearby from damage
through heat.
• Place the soldering iron in holder when not in use.
• Refer to the soldering station operating instructions for further safety information
Operating Elements
1
2 3
4
5
1
Soldering tip
2
Protective barrel
3
Ceramic heating element (internal)
4
Cap nut
Operation
• Unpack the soldering iron and check that all parts are intact.
• Place all equipment on a solid, heat-resistant surface.
• Insert the plug at the end of the power cable (7) into the 4-pin connection socket on the soldering station.
The plug only fits into the socket when the polarity is correct.
• Tighten the nut to secure the plug in place.
• Place the soldering iron into the holder.
Refer to the soldering station operating instructions for further information relating to safety and
operation.
Care and Cleaning
• Before cleaning the soldering tip (1), switch off the power supply and unplug the mains socket from the
mains. Let the soldering iron and soldering station cool down completely.
• The soldering tip does not require any special cleaning. It is sufficient to clean it occasionally by removing
flux residue or excess solder with the sponge.
• The soldering tip must be coated with tin before the soldering station is switched off. This prevents
corrosion on the soldering tip.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause
damage to the housing and malfunctioning.
• Do not use a file or sandpaper to clean the soldering tip. This may damage the soldering tip.
• Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines. You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical Data
Input voltage ......................................... 24 V/DC
Power ................................................... 60 W, max. 90 W
Heating element ................................... Ceramic
Soldering tip .......................................... N9-1
Power plug ............................................ 4-pin connecter
Cable length ......................................... 103 cm
Temperature range ............................... +50 to +480 °C
Operating conditions ............................. -6 to +46 °C, 10 – 90 % relative humidity
Storage conditions ................................ -20 to +60 °C, 10 – 90 % relative humidity
Dimensions (ø x L) ............................... 23.5 x 223 mm
Weight .................................................. 105 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
6
5
Heater holder assembly
6
Rubber grip
7
Power cable
*1953677_v1_0419_02_dh_m_en
7
Werbung
