Conrad GT-730 Bedienungsanleitung Seite 2

O P E R A T I N G I N S T R U C T I O N S
GPS data logger GT-730
Item no. 37 36 86
Intended Use
The USB GPS data logger GT-730 is a GPS receiver with SIRF-4 chipset for position location
and recording up to 256000 values.
The GPS receiver is fi tted with an integrated (non-removable) lithium polymer battery. This
facilitates operation without external power supply.
For data read-out and charging the battery, the GT-730 can be connected to a free USB inter-
face on a PC.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• GPS dongle
• Protective cap
• CD with driver/software
• Operating Instructions
System requirements
• Notebook or desktop PC with a free USB socket
• CD-ROM drive
• Approx. 55 MB free hard disk space
• Operating system: Windows 2000 or later
Description of the Parts
1 ON/OFF switch
2 Data tag key for position marking
3 Status indicator and loading status
4 GPS status indicator / memory status
Explanation of Symbols
The exclamation mark indicates specifi c risks associated with handling, function and
use.
The "Hand" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! The warranty
will be void in such cases.
• The unauthorised conversion and/or modifi cation of the unit is not permitted because of
safety reasons.
• The product is not a toy and should be kept out of the reach of children!
• Protect the product from extreme temperatures, direct sunlight, strong vibrations and com-
bustible gases, vapours and solvents, and moisture.
• Never expose the product to mechanical stress.
• Handle the product with care. The product can be damaged if crushed, struck or dropped,
even from a low height.
If in doubt about how to connect the device correctly, or should any questions arise that are
not answered in these operating instructions, please contact our technical advisory service or
another specialist.
Getting Started
www.conrad.com
a) Charging the battery
The battery needs to be charged for approx. 4 hours before fi rst use, subsequent charging
Version 10/13
usually lasts about 2 hours.
Connect the GT-730 to a USB port of at least 500 mA load capacity. This can be done either
with a USB power supply or a USB interface of your PC.
During the charging process, the status LED (3) lights green. This goes off after a successful
charging process and the device is fully operational. When the rechargeable battery is empty,
the status LED (3) lights red.
b) Switch on/off
Switch the device on or off using the on/off switch (1) by moving the switch to the position
labelled with a dot.
It is recommended to place the GPS logger outside for approx. 15 - 20 minutes before fi rst
use, to ensure the GPS logger recognises all the satellites. This is indicated by the status
indicator (4).
Status LED (4):
steady blue = position not recognised
fl ashes blue (slowly) = position recognised
fl ashes blue (fast) = position data are being recorded
c) Installation of the software / USB driver
Insert the software CD in the CD drive.
Run the fi le named CanWay Installer.exe and follow the instructions on the screen.
When the installation is complete, connect the GT-730 to a free USB interface of your system
and switch it on using the on/off switch (1). The GPS data logger is recognised.
Now start the application.
d) Recording data / data tag
Switch the GT-730 on using the on/off switch (1).
It is recommended to place the GPS logger outside for approx. 15 - 20 minutes before fi rst use,
to ensure the GPS logger recognises all the satellites. This will be indicated by the GPS status
LED (4) (see description under "b) Switch on/off").
To fi x the position, press the data tag key (2). The blue status LED (4) fl ashes rapidly.
Maintenance and Cleaning
You do not need to service the product, apart from occasional cleaning.
Use a soft, antistatic and lint-free cloth for cleaning.
Do not use abrasive or chemical cleaners.
Disposal
Declaration of conformity
The manufacturer hereby declares that this product is in accordance with the fundamental
requirements and the other relevant guidelines of the 1999/5/EG Directive.
After a successful installation, an extensive description of how to use the software
can be found in the installation directory.
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste! Please dispose of the device when it is no longer of use, according to
the current statutory requirements.
The declaration of conformity for this product can be found at www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.