Husqvarna LC 151 Bedienungsanleitung Seite 12

5. Slowly pull out the starter rope until you feel some
resistance.
6. Pull with force to start the engine.
WARNING: Do not twist the starter rope
around your hand.
To use the drive on the wheels LC
151S & LB 256SP
• Push the drive bail in the direction of the handlebar.
(Fig. 27)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
• Before you pull the product rearward, disengage the
drive and push the product forward approximately 10
cm.
To use the drive on the wheels (LB
251S)
• Pull the drive lever in the direction of the handlebar.
(Fig. 28)
• Push the drive lever away from the handlebar to
disengage the drive, for example when you go near
an obstacle.
Note: The drive lever is automatically disengaged
when you release the engine brake handle.
• Before you pull the product rearward, push the drive
lever away from the handlebar and push the product
forward approximately 10 cm to fully disengage the
drive.
To stop the product
• To stop the drive only, release the drive bail (LC
151S, LB 256SP) or the drive lever (LB 251S).
• To stop the engine, release the engine brake handle.
To use the product with the grass
catcher (LC 151, LC 151S)
WARNING: Do not operate the product
without a grass catcher installed or without
the rear cover closed. Objects can eject and
cause injury to the operator.
1. Lift the rear cover and remove the mulch plug if it is
installed. (Fig. 29)
2. Assemble the grass catcher, refer to
the grass catcher (LC 151, LC 151S) on page 11 .
3. Put the grass catcher on the bracket.
4. Release the rear cover and put it on top of the grass
bag frame. (Fig. 30)
12
To change the product to mulch mode
(LC 151, LC 151S)
Make sure the engine is off before you change the
product to mulch mode.
1. Lift the rear cover and remove the grass catcher, if it
2. Put the mulch plug into the discharge channel. (Fig.
3. Close the rear cover and make sure that it is tightly
4. Replace the blade with the mulch blade that is
To change the product to side
discharge mode
1. Lift the rear cover and remove the grass bag, if it is
2. Close the rear cover and make sure that it is tightly
3. Lift the discharge lock. (Fig. 32)
4. Open the side discharge cover and install the side
5. Let the side discharge cover close against the side
To empty the grass catcher
1. Lift the grass catcher with the frame handle.
2. Use the frame handle and the bag handle when you
To get a good result
•
•
To assemble
•
•
•
is installed.
31)
closed against the mulch plug.
supplied in the mulch kit. Refer to
blade on page 14 .
installed.
closed against the product.
discharge deflector onto the support pins. (Fig. 33)
discharge deflector. Make sure that the side
discharge deflector is tightly in position before you
operate the product.
CAUTION: Lift the grass catcher when you
move it to prevent wear.
empty the grass catcher. (Fig. 34)
Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
Do not cut more than ⅓ of the length of the grass.
Use the highest cutting height when you start to cut
the grass. Examine the result and lower the cutting
height to an applicable level. If the grass is very long,
operate slowly and cut 2 times if it is necessary.
Cut in different directions each time to prevent
stripes in the lawn.
Lift the rear cover and remove the grass catcher.
If a mulch plug and a mulch blade are attached,
remove them.
To replace the
1566 - 005 - 07.01.2021