Troubleshooting - Jamara Big Wheel Gebrauchsanleitung

GB
Note
The product is supplied with a wheel hub (2) inside the wheels. This wheel hub (2) could fall out
and end up in the cardboard box. If this is the case, put the wheel hub back into the wheel and
start assembly.
1. Mounting the front wheels
Attach the axle cap (15) to the front as shown in the picture and push the front axle (1)
through. Then push a front wheel (3) with the wheel hub (2) already fi tted onto the front
axle (1). Then press a rim (4) onto the front wheel and secure it by fi rst inserting a small axle
lock (5) and then a small axle cover (6) onto the end of the front axle (1). Repeat this
procedure on the other side.
2. Assembly of the rear wheels
Push the rear wheels (8) onto the rear axle (7) and press the rear rims (9) onto
the wheels until they engage. Secure the wheels by fi rst placing the large axle
lock (10) and then the large axle cover (11) on the ends of the rear axle (7).
Repeat this procedure on the other side.
3. Assembly of the steering wheel
Place the steering wheel (12) on the steering wheel socket (13) and press the
steering wheel into the recess until it engages.
4. Assembly of the seat
Slide the seat (12) onto the corresponding rail of the mudguard (14).
And push it back until it is fi rmly seated.

Troubleshooting

1. The vehicle does not run
● The battery may low on power.
After each use, or once a month minimum, charge the battery. Do not
leave the battery on the charger for more than 15 hours.
● Thermal fuse has tripped.
The vehicle is equipped with a self-resetting fuse. When the
vehicle is overloaded or operated incorrectly; the self-resetting
fuse will be cut off for 5 - 20 seconds before becoming
operational again. The self-resetting fuse is under the seat
Cut off the power, follow these guidelines:
- DO NOT overload the vehicle, Maximum weight allowed: 25 kg
- DO NOT tow anything behind the vehicle.
- DO NOT drive up steep slopes.
- DO NOT drive into fi xed objects, which may cause the wheels to spin, causing the motor
to overheat.
- DO NOT drive in very hot weather, components may overheat.
- DO NOT tamper with the electric system, Doing so may create a short circuit, causing the fuse
to trip.
● Battery connector or wires are loose.
Make Sure the battery connectors are fi rmly plugged in to each other.
● Battery is dead.
Have you properly maintained the battery according to the directions? Is the battery old?
Your battery may need to be replaced.
● Electric system is damaged.
Water may have corroded the system, or loose dirt, gravel or sand might have jammed the
switch.
● Motor is damaged.
The motor needs professional repair.
7
7.1
6
5. Battery connection
Open the bonnet. Connect all connectors as shown. Only plug matching connectors into
eachother and be sure not to reverse the polarity. Make sure the red wire is well connected with
the red terminal on the battery, and same as the black one.
6. Charging Your Vehicle
● The POWER SWITCH must be turned in OFF position when charging.
● Plug the charger port into the input socket and plug the charger plug into a wall outlet.
The battery will begin charging.
● The red LED on your charger is on while the battery is charging. When the green LED comes
on, the battery is fully charged.
● The charge time is between 10 and 15 hours.
● Do not charge the battery more than once within 24 hours.
● Charger and battery heat up during the charging process.
Warning!
• Let the model cool off suffi ciently after each use before putting it back into operation.
When using an additional batteries let it cool off for minimum 15 minutes until the
model is operated again. Overheating can damage the electronics or may result in fi re.
• Always disconnect the model from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
model. Inserting the rechargeable model or charger after charging will result in damage
tothe model, charger or the power supply (fi re hazard).
2. The battery will not recharge
● Battery connector or adapter connector is loose.
Make sure the battery connector and adapter connector are fi rmly plugged together.
● Charger is not plugged in.
Make sure the charger is plugged into the wall outlet and the power fl ow to the outlet is on.
● Charger is not working.
Is the charger warm while charging? If not, the charger may.
3. The vehicle does not run very long.
● Battery may be undercharged.
You may not be charging the battery long enough. After each use, or once a month minimum,
charge the battery. Do not leave the battery on the charger for more than
15 hours.
● Battery is old.
The battery will eventually lose the ability to hold a charge. Depending on the amount of use,
and varying conditions, the battery should operate for one to three years. Replace the battery
with a new one.
4. Battery buzzes or gurgles when charging.
● This is normal and not a cause for concern. It may also be silent when charging, which is also
normal.
5. Charger feels warm when recharging battery.
● This is normal and not a cause for concern.
GB
Starting the model
Press the key (7) into the ignition lock until the light (7.1) is illuminated.
Make sure to remove the key from the ignition after use, otherwise
your battery could be deeply discharged.
Forward / Reverse driving
Set the gear lever to the forward/reverse position.
Press the accelerator pedal to drive the model forwards and backwards.