Operation; Troubleshooting - Renkforce SB505 Bedienungsanleitung

c) Transmitter
1. Remove the existing license plate (keep the screws safe for later).
2. Find an opening that leads into the vehicle.
Important: If drilling a hole, use the sealing ring to prevent water seepage.
3. Route the wires inside the vehicle and connect the:
- Wireless transmitter.
- Speaker module.
4. Attach the license plate and bracket using the removed screws.
5. Connect the transmitter wires.
6. Secure the transmitter and speaker module using the adhesive.
Tilt the camera to find the best results.
d) Receiver (monitor)
1. Secure the monitor to the dashboard using the adhesive.
2. Connect the power socket to the vehicle auxiliary power outlet.
3. The monitor will power up when the
vehicle electric supply is switched
on.

Operation

• When the reverse gear is engaged,
the rear camera will power up and
transmit an image to the monitor.
• The image will include colour
coded parking guides and distance
information.
• Alerts will sound from the speaker.
Distance (m) Safe zone
>2 Safe
1.6 - 2 Safe
1.2 - 1.5 Alarm
1.0 - 1.1 Alarm
0.8 - 0.9 Alarm
0.6 - 0.7 Alarm
0.5 Danger
0.3 - 0.4 Danger
<0.3 Danger
Monitor settings
1. Press MENU to toggle through the following menu items:
Item Description
Brightness Increase / decrease
Contrast Increase / decrease
Saturation Increase / decrease
Zoom 16:9 or 4:3
English (default), German, French, Italian, Spanish, Portuguese, Dutch, Russian,
Language
Chinese, Japanese, Belarusian, Polish, Turkish
Reset Reset to factory default
2. Press +/- to adjust the value of the selected item.
3. Press MENU to save and enter into next menu item, or wait 5 sec to automatically save and exit settings.

Troubleshooting

Error Possible causes
Reverse gear not engaged
The parking aid does No power supply to auxiliary outlet
not turn on.
Incorrect wiring, defective fuse
Speaker volume is in Off position
No sound from speaker
Monitor shows incor-
Program error
rect distance and is
erratic.
Sensors are dirty
Alarm sound Distance / parking lines
No sound Green
No sound Green
●-----●----- Green
●----●----
Green
●---●--- Yellow
●--●-- Yellow
●-●- Red
●●●
Red
●●● Red STOP
Suggestion
Engage reverse
Check power supply
Check all connections and the
fuse feeding the power supply
Switch speaker to Lo or Hi
Disengage then re-engage the
reverse gear (reset)
Clean the sensors
Care and cleaning
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
• Use a damp cloth for heavily soiled areas.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product con-
forms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity:
www.conrad.com/downloads
Select a language by clicking on a flag symbol and enter the product order number in the search
box. You can then download the EU declaration of conformity in PDF format.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
a) Parking sensor
Input voltage / current ........................... 12 V/DC, 470 mA
Operating range .................................... 10.5 - 16 V/DC
Ingress protection ................................. IP67 (camera and sensor module only)
Detection distance ................................ 0.3 - 2.0 m
Ultrasonic frequency ............................. 40 kHz
Cameras ............................................... 1
Sensors ................................................ 2
Image sensor ........................................ CMOS
Total pixels ............................................ 720 x 480
Resolution ............................................. 700 TV lines
Illumination ........................................... min. 0.1 lux
TV system ............................................. PAL (default), NTSC (cut wire)
Camera angle ....................................... 90°
System sensor angle ............................ 110°
Operating/Storage conditions ............... -20 to +70 ºC, 0 – 95 % RH (non-condensing)
Dimensions (W x H x D) ....................... 522 x 135 x 36 mm (license plate frame)
Weight .................................................. 325 g (camera and sensor)
b) Buzzer
Sound level ........................................... max. 100 dB
Cable .................................................... 3.1 m
Buzzer .................................................. 51 x 38 x 22.5 mm
Weight .................................................. 59 g
c) Monitor (receiver)
Size ....................................................... 10.92 cm (4.3 inch)
Resolution ............................................. 480 x 272 px
Cable .................................................... approx 1.9 m
Operating/Storage conditions ............... -20 to +70 ºC, 0 – 95 % RH (non-condensing)
Dimensions ........................................... 117 x 77 x 27.5 mm
Weight .................................................. 146 g incl. cigarette plug
d) Transmitter
Rated voltage ....................................... 12 V/DC
Wireless frequency ............................... 2.414 - 2.468 GHz
Transmission power:............................. 9.312 dBm
Transmission distance .......................... 8 m
Cable length ......................................... approx. 97 cm
Dimensions ........................................... 58 x 35.5 x 15.5 mm
Weight .................................................. 37 g (transmitter)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE. *2267604_v1_0920_02_dh_m_en