Maintenance; Operation - SIOUX SAG03S Serie Bedienungsanleitung Und Teileliste

LUBRICATION
All models may operate without airline lubrication. However, operating the tool without airline lubrication may reduce tool performance and vane life.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and
run the tool for 10-20 seconds to distribute oil through the tool.
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is rec-
ommended.
For Angle Head Die Grinder
Lubricate the angle head assembly with 2 shots of SIOUX #1232A grease every 8 working hours.

MAINTENANCE

Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil
and run for 10 seconds. This will help remove contaminants and reduce the formation of rust.

OPERATION

The tool is equipped with a locking type lever in order to prevent accidental start-up.
Speed of the tool may be adjusted by turning the regulator, which is located opposite the throttle lever.
INSTALLING MOUNTED WHEELS
Insert the mounted wheel into the collet. Make sure the wheel shank and the collet size match. Do not allow the wheel to extend beyond the collet an
excessive distance.
Hold the collet body with a 9/16" (14mm) wrench and the collet nut with a 3/4" (19 mm) wrench.
Turn the collet nut to the right and firmly tighten the collet on to the wheel shank.
REMOVING MOUNTED WHEELS
To remove the mounted wheel, hold the collet body with a 9/16" (14 mm) wrench and the collet nut with a 3/4" (19 mm) wrench.
Turn the collet nut to the left and loosen the collet.
Remove the mounted wheel.
Catalog
Number
SAG03S12
SAG03S20
SAG05S23
SAG7S12
SAG7S15
SAG7S18
SAG7AX13
SAG7AX16
SAG7AX20
SAG10S12
SAG10S15
SAG10S18
SAG10AX12
SAG10AX15
SAG10AX18
SAGA1AX12
SAGS1AX12
SAGA1AX12G
SAGS1AX12G
SAGA1AX15
SAGS1AX15
SAGA1AX15G
SAGS1AX15G
SAGA1AX18
SAGS1AX18
SAGA1AX18G
SAGS1AX18G
Form ZCE747B
Downloaded from www.Manualslib.com
Disconnect tool from air supply before installing or removing wheel or making any adjustments
Noise* (Tested in accordance with
ISO Standard 15744)
*Sound Pressure (dBA) *Sound Power (dBA)
82.3
85.9
86.0
84.3
85.3
85.2
TBD
TBD
TBD
80.7
79.0
80.7
79.5
84.0
80.5
87.4
86.9
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
manuals search engine
WARNING
NOISE AND VIBRATION READINGS
Uncertainty (dBA)
93.9 3.0
97.6 3.0
97.6 3.0
95.9 3.0
96.9 3.0
96.8 3.0
TBD TBD
TBD TBD
TBD TBD
92.4 3.0
90.7 3.0
92.3 3.0
91.1 3.0
95.7 3.0
92.1 3.0
99.0 3.0
98.5 3.0
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
3
Vibration* (Tested in accordance with
ISO Standard 8662-13:1997)
*Vibration m/s^2 Uncertainty m/s^2
5.3 0.7
6.3 1.7
5.2 0.7
1.68 0.02
1.27 0.10
1.75 0.02
TBD TBD
TBD TBD
TBD TBD
1.8 0.1
1.0 0.0
1.6 0.1
1.7 0.1
2.4 0.1
2.1 0.1
2.71 0.71
3.77 0.73
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
TBD TBD
Date 2014October/G