Specifications; Troubleshooting - Gemini CD-140 Bedienungsanleitung

OPERATING INSTRUCTIONS
1. Make sure that the VOLTAGE SELECTOR SLIDE (19) switch, found on
the rear panel, is set for the proper voltage. Plug the unit in and press
the POWER (1) switch. The unit will turn on. Pushing the POWER (1)
switch a second time will turn the unit off.
2. Press the OPEN/CLOSE BUTTON (3), place a CD in the DISC TRAY (2)
and press the OPEN/CLOSE BUTTON (3) again. The tray will close into
the unit.
3. Push the TRACK SKIP BUTTONS (12) to select the track you want to
play.
4. Press the PLAY/PAUSE BUTTON (16) and the unit will instantly play.
CUE INSTRUCTIONS
To start the play at a point other than the beginning of a track, follow these
instructions.
1. To memorize the spot at which you want play to start, select the proper
track, and then push the PLAY/PAUSE BUTTON (16) so the unit goes
into the play mode (play/pause LED will glow green). Listen to the CD
and when the CD gets to the approximate spot, push PLAY/PAUSE
BUTTON (16) so the unit goes into the pause mode (play/pause LED will
blink green). Move the SEARCH JOG WHEEL (9) to the precise spot
you want play to begin and push the PLAY/PAUSE BUTTON (16) to
memorize the cue point. Press the CUE BUTTON (15) to return to the
memorized cue point. Push the PLAY/PAUSE BUTTON (16), and the
unit will instantly play from the spot selected.
2. To fine tune the memorized cue point, push the PLAY/PAUSE BUTTON
(16) so the unit goes into the play mode (play/pause LED glows green)
and listen carefully to the starting point. Push the CUE BUTTON (15) and
the unit will enter the pause mode (play/pause LED blinks green) and the
CD will return to the previously memorized cue point. If you decide that
this point is okay, leave the unit alone until you are ready to play it. At
that time push the PLAY/PAUSE BUTTON (16). The unit will instantly
play from the spot selected. If the selected spot is not where you want it,
with the unit in the play mode, simply push the CUE BUTTON (15). The
unit will go back to the previously selected spot, and enter the pause
mode. By moving the SEARCH JOG WHEEL (9) you can hear and move
the cue point forward or backward. After you have located the spot, push
the PLAY/PAUSE BUTTON (16) to memorize the new cue point. Press
the CUE BUTTON (15) to pause play at the new memorized cue point.
TROUBLE SHOOTING
• If the disk will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
• If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
• If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many CDs are recorded out of spec and will
skip on most or all CD players. Before sending the unit in for repair, try
playing a CD that you are sure plays properly.
Downloaded from www.Manualslib.com manuals search engine

SPECIFICATIONS

GENERAL:
Type..................................................................................Compact Disc Player
Disc Type......................................Standard Compact discs (12 cm & 8 cm)
Time Display..........................Track Elapsed, Track Remain, or Total remain
Variable Pitch............................± 4%, ± 8%, ± 16% Slider with Resume Switch
Pitch Bend......................................................................± 16% Maximum
Instant Start..............................................................Within 0.015 seconds
Track Selection..............................................................................1 to 99 Tracks
Installation.................................................................................19", 2 U
AUDIO SECTION:
Quantization........................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate........................................................................8 Times
Sampling Frequency..........................................................................44.1 kHz
Frequency Response...............................................................20 Hz to 20 kHz
Digital Output........................................................................................IEC958
Total Harmonic Distortion.......................................................Less Than 0.05%
Signal to Noise Ratio..............................................................................104 dB
Dynamic Range.........................................................................................98 dB
Channel Separation.......................................................................90 dB (1 KHz)
Output Level........................................................................1.9 Volts R.M.S.
Power Supply.........................................................AC 115/230V, 60/50 Hz
Dimensions.......................................................19" (W) x 3 1/2" (H) x 10" (D)
Weight......................................................................................9.5s lbs (4 kg)
* Specifications and design are subject to change without notice for purpose
of improvement.
Page 4