Hama 179052 Bedienungsanleitung Seite 7

G Operating instruction
Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please keep
these instructions in a safe place for future reference. If you sell the device, please pass
these operating instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your attention to specific
hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package Contents
• TV Stand (1x)
• Installation kit (see contents, Fig. 1)
• Attachment kit (see contents, Fig. 1)
• These operating instructions
Note
Please check that the installation kit is complete before installing the TV Stand and ensure
that none of the parts are faulty or damaged.
3. Safety Notes
Warning
• Maintain the necessary safety clearance around the attached load (depending on
the model).
• In the event of damage to the product, remove the attached load and stop using
the product.
• Ensure that the electrical cables are not crushed or damaged during installation.
• Do not place loads on the TV stand that are heavier than the specified load bearing
capacity, and do not exceed the specified maximum screen size.
• Ensure that the load on the TV stand is symmetrically balanced.
• Read the operating instructions for your terminal device before attempting to mount
it. The instructions provide information about the type and measurements of suitable
fastening materials.
• If the supplied mounting kit does not contain suitable fastening materials for
mounting the terminal device, purchase these from a specialised dealer.
• Never apply force during installation. This can damage your terminal device or the
product.
• If in doubt, have this product mounted by a qualified technician - do not attempt to
mount it yourself!
• Place the product only on flat, non-slip surfaces that can bear the weight of the product
and the device attached to it.
• Keep the packaging material out of the reach of children due to the risk of suffocation.
• Dispose of packaging material immediately according to locally applicable regulations.
• Do not modify the product in any way. Doing so voids the warranty.
• Do not attach any other objects to the product.
• Do not mount the product above locations where persons might linger.
4. Intended use and specifications
• The product is used for mounting flat panel displays for non-commercial, private
household use.
• The product is intended for indoor use only.
• Use the TV stand for the intended purpose only.
Screen size: 81.0 - 165.0 cm (US: 32" - 65")
Mounting holes: according to the VESA standard until 600x400
Loading capacity: 40 kg
Width / Height / Depth 90.5 cm / 83.0 cm / 34.2 cm
5. Installation requirements and installation
Note
• Only mount the TV stand with the help of a second person! Get the support and
help you need.
• Ensure that no electrical cables are crushed or damaged during installation or
adjusting.
• Once you have mounted the product and the attached load, check that they are
sufficiently secure and safe to use.
• Observe the other warnings and safety instructions.
• Proceed step-for-step in accordance with the illustrated installation instructions (Fig.
1 ff.).
Note
• Given the multitude of terminal devices available on the market, we cannot describe
all possible mounting options here.
• Please ensure that the bracket lays flat and evenly on the back of the television.
• Use the enclosed spacer to even out any unevenness on the back of the television.
• Ensure that all screws have the proper length and can be mounted until they are
hand-tight (see Fig. 3).
6. Setting and maintenance
Note – H eight adjustment
• Only adjust the bracket with the help of a second person. Get the support and help
you need.
• When doing so, ensure that the product does not exceed its maximum permitted
carrying capacity and that no load exceeding the maximum permitted dimensions
is attached (fig. 4).
Note – S et/adjust the tilt
• To permanently set the tilt, loosen the lateral attachment screws, set the desired tilt
and then tighten the screws again (refer to fig. 5).
• To flexibly adjust the tilt, tighten the screws hand-tight. This allows the screen to be
adjusted at any time.
• Check that the bracket is secure and safe to use at regular intervals (at least every three
months). Only use water or standard household cleaners for cleaning.
• To secure the carrying arms, attach them to the TV stand and secure them with the
screws (E3).
• If the rotate function is stiff, loosen the screw on the hinge slightly using the E6 tool
(fig. 5).
7. Securing with an attachment cable
Note
• For screens with a diagonal screen size of more than 55 inches and total height of
more than 100 cm, the holder must be additionally secured to a wall.
• Observe the enclosed warning notice.
Warning
• Before installing the bracket, ensure that the wall on which the television is to be
mounted is suitable for the weight and make sure that no electrical wires, water, gas
or other lines are located at the installation location.
• Please note that the provided wall anchors are only approved for concrete and solid
brick walls.
• If the wall on which the bracket is to be mounted is made of different material types
and construction types to those specified, purchase suitable mounting materials from
a specialised dealer.
• Observe the other warnings and safety instructions.
• Proceed step by step according to the illustrated installation instructions provided in the
enclosed warning notice.
8. Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting
from improper installation/mounting, improper use of the product or from failure to observe
the operating instructions and/or safety notes.
3