General Safety Information - EINHELL Bavaria BLP 100 Gebrauchsanweisung

Anleitung BLP 100 SPK 1 neu

GENERAL SAFETY INFORMATION

12. Don't overreach
Caution! When using electric tools it is impe-
rative to take the following basic safety pre-
cautions in order to reduce the risk of elec-
tric shock, injury and fire. Read and take
13. Look after your tools
note of these instructions before you use
this tool.
1. Keep your work area tidy
– An untidy work area invites accidents.
2. Check the working conditions
them replaced by an authorized specialist.
– Do not expose electric tools to rain.
Check the extension cable regularly and
Never use electric tools in damp or wet
locations. Make sure there is good
lighting. Do not use electric tools near
14. Always pull out the power plug
flammable liquids or gases.
3. Guard against electric shock
– Avoid body contact with earthed compo
nents such as pipes, radiators, cookers,
refrigerators.
4. Keep children away!
15. Remove adjusting keys and wrenches
– Do not allow other persons to touch the
tool or cable. Keep all persons out of your
work area.
5. Store tools in a safe place
16. Avoid unintentional starting
– When tools are not in use they should
be stored in a dry, locked room out of
children's reach.
6. Do not overload your tools
– Tools work better and safer when used
within their quoted capacity range.
17. When using an extension cable outdo
7. Use the right tool
– Never use tools or attachments with
insufficient power for the job in hand.
Never use tools on jobs for which they
18. Be alert at all times
were not intended.
8. Wear suitable work clothes
– Do not wear loose clothing or jewelry as
they may get caught in moving parts.
19. Check the tool for damage
Rubber gloves and non-slip shoes are
recommended when working outdoors.
Wear a hair net if you have long hair.
9. Wear safety goggles
– and use a dust mask when working on
dusty jobs.
10. Do not misuse the cable
– Do not carry the tool by its cable or pull
on the cable to remove the plug from the
socket-outlet. Protect the cable from heat,
oil and sharp edges.
11. Secure your workpiece
– Use clamps or a vise to hold the work
piece securely. This is safer than using
your hand and will enable you to operate
12.02.2003 7:22 Uhr
GB
the machine with both hands.
– Avoid abnormal working postures. Make
sure you stand squarely and keep your
balance at all times.
– Keep your tools sharp and clean for bet
ter and safer performance. Follow the
instructions for maintenance work and for
changing any attachments. Check the plug
and cable regularly and, if damaged, have
replace it if damaged. Keep handles dry
and free from oil and grease.
– when the tool is not being used, before
carrying out any maintenance work and
when changing attachments such as bla
des, bits, grinding belts and cutters of any
kind.
– Make sure that all keys and adjusting
wrenches are removed from the tool befo
re switching it on.
– Never carry a tool with your finger on
the switch if it is connected to the power
supply. Make sure that the switch is in
OFF position when inserting the power
plug.
ors
– check that it is approved for outdoor
duty and is marked accordingly.
– Watch what you are doing. Use common
sense. Do not operate the tool if your mind
is not on your work.
– Each time before re-using the tool,
carefully check that the guards or any
slightly damaged parts are working as
intended. Check that the moving parts are
in good working order, that they do not
jam, and that no parts are damaged. Make
sure that all parts are fitted correctly and
that all other operating conditions are pro
perly fulfilled. Unless otherwise stated in
the operating instructions, damaged
guards and parts have to be repaired or
replaced by an authorized service center.
It is absolutely essential to have damaged
switches repaired by an authorized service
7
Seite 7