Parts Description - Makita DCU180 Betriebsanleitung

PARTS DESCRIPTION

Parts description (when the carrier
is installed)
► Fig.1
1 Control panel
3 Switch trigger
5 Brake lever for front
wheel
7 Brake pedal for rear
wheel
9 Front wheel
Parts description (when the bucket
is installed)
► Fig.2
1 Control panel
3 Switch trigger
5 Brake lever for front
wheel
7 Brake pedal for rear
wheel
9 Front wheel
ASSEMBLY
CAUTION:
Always be sure that the machine is
switched off and the battery cartridge is removed
before carrying out any work on the machine.
Assembling main unit
1. Take out the base unit and handles from the box.
► Fig.3
NOTICE:
Be sure to take out the base unit and
handles together, so that excessive force is not
applied to the cords.
2. Place the packing material under the rear side of
the base unit.
► Fig.4: 1. Packing material
3. Insert the rear wheels into the frame.
► Fig.5: 1. Rear wheel
► Fig.6: 1. Rear wheel
NOTE: The support legs can be attached instead of
the rear wheels.
4. Attach the spring washer and the washer to the
short hexagonal bolt, and then tighten them using the
wrench included in the package.
► Fig.7: 1. Short hexagonal bolt 2. Spring washer
3. Washer
► Fig.8
2 Handle
4 Battery box
6 Rear wheel
8 Lamp
10 Carrier
2 Handle
4 Battery box
6 Rear wheel
8 Lamp
10 Bucket
NOTICE:
Be sure to use the short hexagonal
bolts to tighten the rear wheels.
NOTICE:
Fix the rear wheels at the same position
on both sides.
5. Raise the handles, and then insert them into the
base unit.
► Fig.9
NOTICE:
Do not allow the cords inside area "A"
in the figure. Long objects may be entangled with the
cords and cause accidents.
NOTICE:
Do not apply excessive force to the
cords when raising and inserting the handles.
NOTICE:
Be sure to raise the handles with both
hands.
6. Open the carrier frame toward the front.
► Fig.10: 1. Carrier frame
7. Unfold the handles, then insert the long hexagonal
bolts into the base unit, and then tighten the nuts with
the wrench included in the package.
► Fig.11: 1. Long hexagonal bolt
8. Tighten the shoulder bolts from the rear using the
wrench included in the package.
► Fig.12: 1. Shoulder bolt
9. Tighten the short hexagonal bolts from both sides
using the wrench included in the package to fix the
handles.
► Fig.13: 1. Short hexagonal bolt
NOTICE:
Do not tighten the short hexagonal
bolts with excessive force. Tighten them with
proper force so that the handles are stably fixed.
NOTICE:
Do not pinch the cords with the bolts.
10. Fix the cords with the clamps.
► Fig.14: 1. Clamp
11. Fold the carrier frame.
► Fig.15: 1. Carrier frame
12. Press the lock button while pulling the brake lever
to lock the brake.
► Fig.16: 1. Lock button 2. Brake lever
CAUTION:
If the rear wheels are installed,
press the brake pedal for the rear wheel to lock
the rear wheel.
13. Hook the carrier lock, and then pull down the lock
lever to lock the carrier.
► Fig.17: 1. Carrier lock 2. Lock lever
NOTICE:
Make sure that the lock lever is locked
securely.
NOTICE:
Do not pinch the cords with the lock
lever.
NOTE: If you attach the support legs instead of the
rear wheels, remove the rear wheels from the frames,
and then attach the support legs to the frames.
► Fig.18: 1. Rear wheel 2. Support leg
17 ENGLISH