ASROCK K10N78FullHD-hSLI Schnellinstallationsanleitung Seite 34

2 . 1 2 2 . 1 2 Serial A 2 . 1 2 Serial AT T T T T A (SA Serial A Serial A A (SA A (SA A (SAT T T T T A) / Serial A
2 . 1 2 2 . 1 2 Serial A A (SA
Installation Installation Installation Installation Installation
This motherboard adopts NVIDIA
(SATA) / Serial ATAII (SATAII) hard disks and RAID (RAID 0, RAID 1, RAID 0+1, RAID 5
and JBOD) functions. You may install SATA / SATAII hard disks on this motherboard
for internal storage devices. This section will guide you to install the SATA / SATAII
hard disks.
STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.
STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.
STEP 3: Connect one end of the SATA data cable to the motherboard's SATAII
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard
disk.
1. If you plan to use RAID 0, RAID 1 or JBOD function, you need to install at
least 2 SATA / SATAII hard disks. If you plan to use RAID 5 function, you
need to install 3 SATA / SATAII hard disks. If you plan to use RAID 0+1
function, you need to install 4 SATA / SATAII hard disks.
2. Under non-RAID mode, SATAII_5 (PORT4) and SATAII_6 (PORT5)
cannot function.
2.13 Hot Plug and Hot Swap F 2.13 Hot Plug and Hot Swap F 2.13 Hot Plug and Hot Swap Functions for SA
2.13 Hot Plug and Hot Swap F 2.13 Hot Plug and Hot Swap F
HDDs HDDs
HDDs HDDs HDDs
This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII Devices
in RAID / AHCI mode. NVIDIA
Advanced Host controller Interface (AHCI), a new programming interface for SATA host
controllers developed thru a joint industry effort. AHCI also provides usability enhancements
such as Hot Plug.
NOTE
What is Hot Plug Function?
If the SATA / SATAII HDDs are NOT set for RAID configuration, it is
called "Hot Plug" for the action to insert and remove the SATA / SATAII
HDDs while the system is still power-on and in working condition.
However, please note that it cannot perform Hot Plug if the OS has
been installed into the SATA / SATAII HDD.
What is Hot Swap Function?
If SATA / SATAII HDDs are built as RAID 1 or RAID 5 then it is called
"Hot Swap" for the action to insert and remove the SATA / SATAII
HDDs while the system is still power-on and in working condition.
3 4 3 4 3 4
3 4 3 4
ASRock
A) / Serial AT T T T T AII (SA A) / Serial A A) / Serial A AII (SAT T T T T AII) Hard Disks AII (SA AII (SA
A) / Serial A AII (SA
®
GeForce 8200 chipset that supports Serial ATA
unctions for SAT T T T T A / SA unctions for SA unctions for SA
unctions for SA
®
GeForce 8200 chipset provides hardware support for
K10N78FullHD-hSLI Motherboard
AII) Hard Disks AII) Hard Disks AII) Hard Disks
AII) Hard Disks
A / SAT T T T T AII A / SA A / SA AII AII AII
A / SA AII