Balluff BOS 18M-P/NA-LR10 Serie Betriebsanleitung Seite 4

Wiring diagramms
Typ ...LR10-S4/02
Pin Cable
1 brown
2 white
3 blue
4 black
Typ ...LR10-S4S
Pin Cable
1 brown
2 white
3 blue
4 black
Fig. 2: Connection diagram, pinouts
Setting
Standard setting
1. Position sensor and reflector at desired distance.
2. Set the potentiometer for the maximum sensitivity
(longest range).
3. Determine the on­ and off switching point of the output
(yellow LED): Move the sensor in all directions so that
the yellow LED on the normally open version turns on
and off again, or off to on for the normally closed
version.
4. Install the sensor in the center of the determined
switching points.
Fine adjustment for detecting very small objects
1. First perform the standard setting (see above).
2. Then turn the potentiometer counter­clockwise until the
yellow LED comes on (normally open version) or goes
off (normally closed version). The reflector will no longer
be detected.
3. Now turn the potentiometer slowly clockwise until the
yellow LED goes out (normally open version) or comes
on (normally closed version). The reflector will be
detected again. Now even very small objects can be
detected.
Disposal
This product falls under the current EU
Directive for WEEE, waste of electrical and
electronic equipment for protecting you and
the environment from possible hazards and
responsible handling of natural resources.
Dispose of the product properly and not as part of the
normal waste stream. Observe the regulations of the
respective country. Information can be obtained from the
national authorities. Or return the product to us for
disposal.
10...30 V DC
Output light­on mode, N.C.
0 V
Output dark­on mode, N.O.
10...30 V DC
Output dark­on mode, N.O.
0 V
Output light­on mode, N.C.
Technical Data
Optical
Range s on reflector BOS R­1
r
BOS 18M­...
BOS 18MR­...
Light type emitter
Laser class IEC 60825­1:2014
Wavelenght l
Average power
Pulse frequency Laser
Pulse width
Electrical
Supply voltage U
B
Rated operating voltage U
e
Ripple (% from U )
e
No­load current I
O
Effective operating current I
e
Voltage drop U at I
d e
Turn­on delay
Turn­off delay
Switching frequency f
Output depending on version
Short circuit protected
Reverse polarity protected
Switching function depending on
version
Output function depending on
version
Sensitivity setting
Mechanical
Connection type depending on
version
Housing material
Active surface material
Housing dimensions BOS 18M­
Cable version
Connector version
Housing dimensions BOS 18MR­
Cable version
Connector version
Weight
Cable version
Connector version
Displays
Output function indicator
Power on indicator
Ambient
Ambient temperature T
a
Enclosure rating per IEC 60529
Ambient light rejection according to
IEC 60947­5­2
IND. CONT. EQ
1TD4
C US
for use in the secondary of
a class 2 source of supply
LISTED
Balluff GmbH
Schurwaldstrasse 9
73765 Neuhausen a.d.F.
Germany
Phone +49 7158 173­0
Fax +49 7158 5010
Service­Center +49 7158 173­370
service@balluff.de
english
0.1...16 m
0.1...9 m
Laser red light
1
630...680 nm
< 100 µW
25 kHz
6 µs
10...30 V DC
24 V
≤ 10%
≤ 35 mA
≤ 100 mA
≤ 2 V
≤ 333 ms
≤ 333 ms
1.5 kHz
PNP or NPN
yes
yes
N.O. or N.C.
dark­on or light­on
Potentiometer
M12 connector, 4­pin
Cable 2 m, Ø 4 mm
Cu­Zn Nickel plated
PMMA
77 mm, Ø M18x1
81,5 mm, Ø M18x1
89 mm, Ø M18x1
93,5 mm, Ø M18x1
110 g
60 g
yellow LED
green LED
–10... +50 °C
IP67
5 kLux
1