Specifications; Intended Use - Makita DTDA040 Betriebsanleitung

ENGLISH ( Original instructions)

SPECIFICATIONS

Model:
F astening c apac ities
Max imum f astening torq ue
T orq ue range
No load speed ( R P M)
I mpac ts per minute
R ated v oltage
O v erall length
Net w eigh t
Due to our continuing program of research and development, the specifications herein are subject to change
w it h out noti c e.
Specifications may differ from country to country.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est c ombination, a c c or d ing to E P T A - P ro c e d ure 0 1 / 20 1 4 , are s h o w n in t h e table.
Applicable battery cartridge and charger
Battery cartridge
C h arger
Some of the battery cartridges and chargers listed above may not be available depending on your region of
resi d en c e.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

T h e tool is inten d e d f or s c re w d ri v ing in w oo d , metal
an d plasti c .
Noise
The typical A-weighted noise level determined accord-
ing to EN 6 2 8 4 1 -2-2 :
Model DTDA040
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 0 1 d B ( A )
W A
Uncertainty (K) : dB(A)
Model DTDA070
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 03 d B ( A )
W A
Uncertainty (K) : dB(A)
Model DTDA100
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 0 5 d B ( A )
W A
Uncertainty (K) : dB(A)
Model DTDA140
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 0 5 d B ( A )
W A
Uncertainty (K) : dB(A)
S tand ard bolt
H igh tensile bolt
) : 9 0 d B ( A )
pA
) : 9 2 d B ( A )
pA
) : 9 4 d B ( A )
pA
) : 9 4 d B ( A )
pA
DTDA040 DTDA070
M5 - M1 0
M5 - M8
35 N• m 6 5 N• m
A pprox . A pprox .
3 - 20 N• m 5 - 4 0 N• m
-1
0 - 2,4 00 min 0 - 2,5 00 min
-1
0 - 3,700 min
1 39 mm
1 .1 - 1 .4 kg
BL 1 4 1 5 N / BL 1 4 1 5 NA / BL 1 4 30 / BL 1 4 30B / BL 1 4 4 0 / BL 1 4 5 0 /
BL 1 4 6 0A / BL 1 4 6 0B
D C 1 8 R C / D C 1 8 R D / D C 1 8 R E / D C 1 8 S D / D C 1 8 S E / D C 1 8 S F /
NOTE: T h e d e c lare d noise emission v alue ( s ) h as
been measure d in a c c or d an c e w it h a stan d ar d test
method and may be used for comparing one tool with
anot h er.
NOTE: T h e d e c lare d noise emission v alue ( s )
may also be used in a preliminary assessment of
e x posure.
WARNING:
W ear ear protection.
WARNING:
The noise emission during actual
use of the po w er tool can differ from the declared
value ( s ) depending on the w ays in w hich the
tool is used especially w hat kind of w orkpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use ( taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
off and w hen it is running idle in addition to the
trigger time ) .
5 ENGLISH
DTDA100 DTDA140
M5 - M1 2 M6 - M1 6
M5 - M1 0 M6 - M1 2
9 5 N• m 1 4 0 N• m
A pprox . A pprox .
6 - 6 5 N• m 1 8 - 8 0 N• m
-1
0 - 2,700 min
0 - 3,300 min
D .C . 1 4 .4 V
1 4 6 mm
1 .2 - 1 .4 kg 1 .2 - 1 .5 kg
D C 1 8 S H
-1
-1