Makita DTDA040 Betriebsanleitung Seite 11

LED indicator / beeper
Fig.12: 1. L E D in d i c ator
L E D in d i c ator / beeper on t h e tool s h o w s t h e f ollo w ing f un c tions.
Alarm No.
E0 Battery installation
error
E1 A uto-stop
E2 A nti-reset of
c ontroller
E3 A uto-stop w ith low
remaining battery
capacity
E4 O v erload protec tion
E5 O v erh eat protec tion
E6 Motor loc k
E7 Motor f ailure
E8 S w itc h f ailure
E9 A larm f or a long
period of use
- A uto-stop w ith f as-
tening c ompletion
- Alarm for insufficient
f astening
- A larm f or limit of th e
fastening capacity
- Maintenanc e alarm
Function Status of the tool
If the battery car-
trid ge is installed
w ith th e sw itc h
trigger pulled , th e
tool stops to av oid
unintentional start.
The battery power
bec ame low and it is
time to replac e th e
battery cartridge.
The battery voltage
d ropped abnor-
mally for some
reason, and th e tool
stopped .
The battery power is
almost used up and
th e tool stopped .
T h e tool w as ov er-
load ed and stopped .
T ool' s c ontroller
h eated up abnor-
mally and the tool
stopped .
T h e motor h as been
loc ked . A t th is time,
th e tool d oes not
w ork.
T h e tool d etec ted a
motor f ailure. A t th is
time, tool d oes not
w ork.
T h e tool d etec ted a
sw itc h f ailure.
T h e tool h as been
turned on f or a long
time ( A pprox . 3
minutes) .
T h e preset f asten-
ing torq ue h as been
ac h iev ed and th e
tool h as stopped .
T h e preset f as-
tening torq ue h as
not been ac h iev ed
bec ause th e sw itc h
trigger w as released
bef ore c ompleting
th e f astening.
–
T h e number of d riv e
h as been reac h ed to
your preset number
f or th e maintenanc e.
Status of the LED indicator/beeper
LED indicator
Blinks in red and
green alternatively.
Blinks in red and
green alternatively.
Blinks in red and
green alternatively.
L igh ts up in red .
Blinks in red and
green alternatively.
Blinks in red quickly.
Blinks in red and
green alternatively.
Blinks in red and
green alternatively.
Blinks in red and
green alternatively.
Blinks in red and
green alternatively.
L igh ts up in green
for approximately
one sec ond .
L igh ts up in red f or
approximately one
sec ond .
Blinks in red quickly.
Blinks in yellow.
11 ENGLISH
Action to be taken
Beeper
A series of long Install the battery
beeps c artrid ge w ith
th e sw itc h trigger
released .
A series of long Replace the battery
beeps with fully charged
one.
A series of long Replace the battery
beeps with fully charged
one.
A long beep Replace the battery
with fully charged
one.
A series of long R emov e th e c ause
beeps of ov erload , and
th en restart th e tool.
Ask your local
Makita S erv ic e
C enter f or repair.
A series of long Remove the battery
beeps c artrid ge immed i-
ately and cool the
tool d ow n.
A series of long R elease th e sw itc h
beeps trigger and pull it
again.
A series of long Ask your local
beeps Makita S erv ic e
C enter f or repair.
A series of long Ask your local
beeps Makita S erv ic e
C enter f or repair.
A long beep R elease th e sw itc h
trigger and pull it
again.
–
A long beep R etigh ten th e
f astener.
A series of long Replace the battery
beeps with fully charged
one.
– R eset th e alarm
w ith th e applic ation
sof tw are.
–