Operation - Renkforce 2233287 Bedienungsanleitung

Operating instructions
Wilderness camouflage camera 2m pixel video re-
cording
Item no. 2233287
Intended use
The product is intended for the creation of digital photo and video recordings. The product has
an in-built camera, which is triggered by a PIR sensor. It allows animals such as deer or birds to
be photographed and filmed undisturbed. Photos and videos are recorded onto an SD memory
card (max. 32 GB). Power is supplied by four AA batteries.
For safety and approval purposes, do not rebuild and/or modify this product. Using the product
for purposes other than those described above may damage the product. In addition, improper
use can cause hazards such as a short circuit or fire. Read the operating instructions carefully
and store them in a safe place. Only make this product available to third parties together with
its operating instructions.
This product complies with statutory, national and European regulations. All company and pro-
duct names contained herein are trademarks of their respective owners. All rights reserved.
Delivery content
• Wilderness camera • 3x dowels
• Belt strap • Holder
• 3x screws • Mounting base
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in a triangle indicates that there is a risk to your health,
e.g. due to an electric shock.
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and tips on how to use the product.
Safety information
Read the operating instructions and safety information carefully. If you do not
follow the safety information and information on proper handling in these ope-
rating instructions, we will assume no liability for any resulting personal inju-
ry or damage to property. Such cases will invalidate the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a dange-
rous plaything for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, stop using it and prevent
unauthorised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Handle the product carefully. Jolts, impacts or a fall even from a low height may
damage the product.
• Consult a technician if you are not sure how to use or connect the product, or if
you have concerns about safety.
• Maintenance, modifications and repairs must be carried out by a technician or a
specialist repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Connected devices
• Always observe the safety information and operating instructions of any other de-
vices which are connected to the product.
Controls
• Mini USB cable
• Operating instructions
22
1 Lens
2 Infrared LEDs
3 LED indicator
4 Microphone
5 PIR sensor
6 Slide switch position ON
7 Slide switch position

Operation

a) Inserting/replacing the batteries
• To insert the batteries into the battery compartment (13), first undo the fastening clip (21)
• Then, open the wilderness camera by folding the halves of the housing apart.
• Insert four AA batteries with correct polarity (not included). Observe the '+' and '-' markings
• The LED indicator (3) flashes briefly.
• If the battery symbol on the LC display (20) indicates a low battery level, replace the batte-
b) Operating the wilderness camera with a power adapter
• The camera can be optionally operated with a power adapter. It has a priority circuit for the
• Connect the low-voltage plug of a suitable power adapter (see 'Technical data') to the low-
c) Batteries
• Check that the batteries are inserted with the correct polarity.
• To prevent battery leakage, remove the batteries if you do not plan to use the
product for an extended period. Leaking or damaged batteries may cause acid
burns if they come into contact with your skin. Always use protective gloves when
handling damaged batteries.
• Keep batteries out of the reach of children. Do not leave batteries lying around, as
there is a risk that children or pets may swallow them.
• Replace all of the batteries at the same time. Mixing old and new batteries can
cause the batteries to leak and damage the product.
• Batteries must not be dismantled, short-circuited or thrown into fire. Never rechar-
ge non-rechargeable batteries. This may cause an explosion!
2
1
9
3
4
5
13
15
16
21
8 Slide switch position OFF
9 USB connection
10 DC low-voltage socket
11 AV video connection
12 Speaker
13 Battery compartment
14 MENU button
SETUP
15 Left arrow button
Ensure that the slide switch is in the SETUP (7) or OFF (8) position before inserting
the batteries.
on the right-hand side of the housing and fold it down.
in the battery slots.
ries with new ones. Proceed as described above, but remove the old batteries first.
When using rechargeable batteries, expect a shorter operating duration due to the
lower operating voltage (non-rechargeable battery = 1.5 V/cell, rechargeable battery
= 1.2 V/cell). Moreover, rechargeable batteries are more temperature sensitive than
normal batteries. Therefore, rechargeable batteries have a very short operating du-
ration at low temperatures. If you want to use rechargeable batteries despite these
limitations, we recommend the use of NiMH batteries with low self-discharge.
power supply with direct current. You do not need to remove the batteries before connecting
the power adapter.
voltage DC socket (10) in order to supply the camera with power via the power adapter.
The power adapter is not included with the product.
6 7 8
10
11
12
14 17
18
19
20
16 PLAY button
17 OK button
18 Right arrow button
19 SHOT button
20 LCD display
21 Fastening clip
22 Tripod socket