Operating Elements; Operation - Renkforce 2299532 Bedienungsanleitung

Operating elements

1 MODE Key
2 Slide switch key
3 UP Key
4 OK/SHOT Key
5 DOWN Key
Keys Functions
Slide switch key 1. OFF: Power off
2. SETUP: Setting mode.
3. ON: Monitoring mode.
MODE key 1. Short press to switch back and forth between recording, taking pho-
tos, playback, and menus.
2. In submenus, short press to return to the previous menu.
UP key 1. Move upwards in the settings menu.
2. Move upwards to select a number in the time setting or password
protection menu.
OK/SHOT 1. In the video or photo interface, short press to take pictures and vid-
eos.
2. In the settings menu, short press OK to confirm your selection.
DOWN key 1. Move downwards in the settings menu.
2. Move downwards to select a number in the time setting or password
protection menu.
3. In playback mode, long press to display the delete menu, and then
choose whether to delete a single file or delete all.

Operation

1. Inserting the batteries/using the power adapter
Ensure that batteries are placed in the camera before use.
• To insert the batteries, press the battery box button (6) and take out the battery box. Then
insert four/eight 1.5 V AA batteries into the battery slot with correct polarity (observe the "+"
and "-" markings in the battery slots).
• When using the power adapter (not supplied) to power the product, open the round rubber
seal on the base plate and then connect the plug on the adapter cable into the socket.
2. Inserting/removing the memory card
• Insert a memory card into the corresponding slot until it clicks into place.
• To remove the memory card, push the card slightly in order to release it from the slot.
SD
Note: The camera does not have a built-in memory, so a memory card must be inserted into
the camera before use. If the memory card has been used in a different camera, format the
memory card in the wildlife camera before use.
Switching on and off
• To switch the wildlife camera on, slide the slide switch (2) to the SETUP position. The
welcome screen will appear on the LC display (7).
• Set the slide switch to the OFF position to switch the wildlife camera off.
Settings and functions in the OSD menu
The following settings are available:
1. SETUP mode
In SETUP mode, the infrared lamp is disabled so that test shots can be taken. Slide the slide
switch (2) from OFF to SETUP to turn the camera on. Press the MODE (1) key to toggle
between video/photo recording, playback and menu modes. Press OK (4) to save the settings.
In video/photo recording modes, short press SHOT (4) to record video or take a photo. Press
MODE (1) one more time to return to the previous menu or exit the menu settings. Slide the
slide switch (2) to OFF to power off the camera.
6 Battery box button
7 LCD
8 Speaker
9 SD card slot
2. Operating modes
The wildlife camera has three operating modes: Photo, Video and Photo+Video. Photo mode
includes 1 MP, 3 MP, 5 MP, 8 MP, 12 MP, 16 MP and 20 MP resolution options. Video mode
includes 1080p, 720p, WVGA and VGA resolution options. Higher resolution photos/videos
are more detailed but take up more space on the memory card. In Photo+Video mode, the
camera takes a photo and then starts recording video. Note: When recording video, the camera
automatically enters power saving mode and the screen turns off. To turn the screen on again,
press any key on the camera.
3. Video length
The length of recorded video can be set from 3 to 60 seconds and from 1 to 10 minutes. The
longer the selected recording time, the shorter the possible operating time. The pre-set video
length is 5 seconds.
4. PIR interval
The shot lag time can be set from 5 to 60 seconds and from 1 to 60 minutes.
During the selected interval, the camera will not record photos or videos. This prevents the
memory card from being filled up with too many recordings of the same event.
5. PIR sensor sensitivity
The sensitivity of the main motion sensor can be set depending on environmental conditions.
Select "High" for interiors and environments with little interference, "Medium" for exteriors and
environments with a normal amount of interference, and "Low" for environments with a high
level of interference.
6. Working timer
The daily target recording time and duration can be set. After this time, the camera will remain
on standby. To set the target recording time, go to the menu and enter the "Target recording
time" menu. Press OK (4) and then select "ON" to set the target start and end recording time.
7. Time lapse
Time lapse mode can be used to automatically take a photo at regular time intervals. To set time
lapse settings, go to the menu and enter the "Time lapse" menu. Press OK (4) and then select
"ON" to set the time interval and Hr, Min and Sec values accordingly.
8. System time setting
To set the time and date format, go to the menu and enter the "Time & Date" menu. Press
OK (4) and select "OK" to make changes to the time and date. Press UP/DOWN to select the
desired number and press UP (3)/DOWN (5) to change to value. Press OK (4) to confirm your
changes.
Time format: 12/24 hr
Date format: DD/MM/YYYY, YYYY/MM/DD, MM/DD/YYYY
9. Password setting
To set the camera's power-on password, go to the menu and enter the "Password Setting"
menu. Select "ON" to set a 4-digit number password. If you forget the power-on password,
press OK+Up while the camera is turned off and then switch the slide switch to SETUP mode
to unlock the camera.
10. Camera ID
To set a unique serial number for the camera, go to the menu and enter the serial number
setting menu. Press OK (4) and select "ON" to set a 4-digit combination of digits or letters
between 0-9/A-Z.
11. Playback
To view photos/videos recorded by the camera, remove the camera from the installed position,
slide the switch (2) to SETUP and press MODE (1) 3 times to enter Playback mode. Press
UP (3)/DOWN (5) to view recorded photos/videos. When playing back recorded videos, press
OK (4) to start playback and press OK (4) to stop playback.
• The "Delete selection" function can be used to delete the currently selected photo/video
from the memory card. Press MODE (1) 3 times to enter Playback mode. Press and hold
DOWN (5) to enter the delete menu and select "Delete Selection" and then "Delete Single".
Press OK (4) to confirm or press MODE (1) to exit.
• The "Delete all" function can be used to delete all photos/videos from the memory card.
In Playback mode, press and hold DOWN (5) to enter the delete menu and select "Delete
Selection" and then "Delete All". Press OK (4) to confirm or press MODE (1) to exit.