43cm (17-zoll) lcd/tft monitor mit led hintergrundbeleuchtung
48 cm (19-zoll) lcd/tft monitor mit led hintergrundbeleuchtung
48 cm (19-zoll) lcd/tft monitor mit led hintergrundbeleuchtung (15 Seiten)
1. Important Safety Instructions Do not insert sharp objects or spill liquid into the monitor through the ventilation holes. This may cause fire, electric shock or failure. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials or other risks.
UL/TUV approved computers with receptacle rated 100-240 V AC, 50/60 Hz, 2.0 A (minimum). Check the monitor specification carefully. The GML-2810U has a maximum resolution of 3840(H) x 2160(V) and works with both PAL and NTSC signal modes. The monitor was made for 24/7 security purposes;...
4. Rear View with Connections Power DVI, HDMI2, HDMI1, DP, Audio In, Audio Out Power: Connect the power cord which is included in the package. DVI: Connect the monitor to a video source with the DVI connection HDMI1 & HDMI2 (High Definition Multimedia Input): Here you can connect a monitor with a HDMI cable (the cable is not included in the package).
6. OSD Control Keys Function 1 MENU Show OSD menu/ Select function 2 DOWN Move icon down/ decrease value/ Open Colour Effect 3 UP Move icon up/ Increase value/ Open Input Source Selection 4 EXIT Back to last menu / Auto-adjust Turn OFF / ON 7.
9.3. Picture In the Picture menu you can adjust all settings that are connected to the image adjustments. Press the “UP” or “DOWN” button to select the menu you want to adjust. Press the “MENU” button to select the submenu. And change the value with the “UP” or “DOWN”...
Phase (0-100 Adjust the frequency of the input signal to match that of the display. Sharpness (0-4 Increase or decrease the boundaries between light and dark areas. 9.5. Colour In the Colour menu you can adjust all the settings that are connected to the colour settings of the input source.
DP Option (1.2, 1.1): Change the DisplayPort configuration. Aspect Ratio (Full, 16:9, 4:3, 5:4, 1:1): Change the ratio of the image on the display regardless of incoming signal. DDCCI (Off, On): Display Data Channel / Command Interface. Enable this to allow a computer to send commands to the display.
9.8. Audio In the audio menu you can adjust all the settings that are connected to the audio adjustments. Press the “UP” or “DOWN” button to select the menu you want to adjust. Press the “MENU” button to select the submenu. And change the value with the “UP” or “DOWN” buttons. Press the “EXIT”...
Seite 12
Transparency (0-100): Adjust the transparency of the OSD on the display. Reset: Return the display to factory settings. Information: Current display input and resolution. Frequently Asked Questions The Power button does not respond: - Check the power cord to ensure that it is securely plugged into the monitor base and also into the electrical outlet.
EC Declaration of Conformity GML-2810U 71 cm (28") UHD LCD/TFT Monitor LED Backlight It is hereby certified that the products meet the standards in the following relevant provisions: EC EMC Directive 2014/30/EU Low Voltage Directive 2014/35/EU Applied harmonised standards and technical specifications:...
1. Wichtige Sicherheitshinweise Stecken Sie keine scharfen Gegenstände in den Monitor oder verschütten Sie keine Flüssigkeiten durch die Belüftungsöffnungen. Dies kann zu einem Brand, einem elektrischen Schlag oder einem Ausfall des Monitors führen. Versuchen Sie nicht, das Gerät selbst zu warten, da Sie sich durch das Öffnen oder das Abnehmen der Deckel der Einwirkung gefährlicher Spannungen oder anderen Risiken aussetzen könnten.
50/60 Hz, 2,0 A Anschluss ausgestattet sein. Überprüfen Sie die Spezifikationen des Monitors gewissenhaft. Der GML-2810U hat eine maximale Auflösung von 3840(H) x 2160(V) und arbeitet im PAL- und NTSC-Signalmodus. Der Monitor ist zum Betrieb rund um die Uhr ausgelegt, daher müssen die Umgebungs- bedingungen wie Betriebstemperatur und Spannung jederzeit gewährleistet sein.
4. Unteransicht mit Anschlüssen DVI, HDMI2, HDMI1, DP, Audioeingang, Netzeingang Audioausgang Netzeingang: Schließen Sie hier das mitgelieferte Netzkabel an. DVI: Schließen Sie hier eine Videoquelle mit DVI-Anschluss an. HDMI1 und HDMI2 (High Definition Multimedia Input): Schließen Sie hier ein Gerät über HDMI- Kabel an (Kabel gehört nicht zum Lieferumfang).
6. Bedientasten für das Bildschirmmenü Taste Funktion 1 MENU Anzeige des Bildschirmmenüs/Auswahlfunktion 2 DOWN Cursor abwärts/Wert verringern/Farbeinstellung aufrufen 3 UP Cursor aufwärts/Wert erhöhen/Auswahl der Eingangsquelle aufrufen 4 EXIT Zurück in das vorherige Menü/Automatische Einstellung Monitor ein- und ausschalten 7. Eingangsquelle wählen Drücken Sie „UP“, um das Menü...
8.3 Bild Im Bildmenü nehmen Sie die Bildeinstellungen vor. Drücken Sie „UP“ oder „DOWN“ zur Auswahl des einzustellenden Menüs. Drücken Sie „MENU“ zur Auswahl des Untermenüs. Stellen Sie den Wert mit „UP“ oder „DOWN“ ein. Drücken Sie „EXIT“, um zur Auswahl des Untermenüs zurückzukehren.
Hier stimmen Sie die Frequenz des Eingangssignals auf die Anzeige ab. Schärfe (0-4): Hier erhöhen oder verringern Sie die Grenzen zwischen hellen und dunklen Bereichen. 8.5 Farbe Im Farbmenü nehmen Sie die Farbeinstellungen der Eingangsquelle vor. Drücken Sie „UP“ oder „DOWN“...
DP-Option (1.2, 1.1): Hier ändern Sie die DisplayPort-Konfiguration. Seitenverhältnis (Voll, 16:9, 4:3, 5:4, 1:1): Hier stellen Sie das Bildseitenverhältnis unabhängig vom Eingangssignal ein. DDCCI (Aus, Ein): Anzeige Datenkanal/Befehlsschnittstelle. Aktivieren, um einem Computer die Übertragung von Befehlen an den Monitor zu ermöglichen. DP EDID (4K2K bei 60 Hz, 1080p, 2560 x 1440, 4K2K bei 30 Hz): DisplayPort Extended Display Identification Data.
D3 DVI: Wählen Sie manuell den DVI-Port als Eingangsquelle. 8.8 Audio Im Audiomenü nehmen Sie die Audioeinstellungen vor. Drücken Sie „UP“ oder „DOWN“ zur Auswahl des einzustellenden Menüs. Drücken Sie „MENU“ zur Auswahl des Untermenüs. Stellen Sie den Wert mit „UP“ oder „DOWN“ ein. Drücken Sie „EXIT“, um zur Auswahl des Untermenüs zurückzukehren.
Hier stellen Sie die vertikale Position des Bildschirmmenüs auf dem Monitor ein. Transparenz (0-100): Hier stellen Sie die Transparenz des Bildschirmmenüs auf dem Monitor ein. Rücksetzen: Hier setzen Sie den Monitor zu den Werkseinstellungen zurück. Information: Hier werden der aktuelle Eingang und die Auflösung angezeigt. ...
EG-Konformitätserklärung GML-2810U 71 cm (28") UHD LCD/TFT-Monitor mit LED- Hintergrundbeleuchtung Es wird hiermit bestätigt, dass die Produkte in der serienmäßigen Ausführung folgenden einschlägigen Bestimmungen entsprechen: EG-EMV Richtlinie 2004/108/EG Angewendete harmonisierte Normen und technische Spezifikationen: EN 50130-4: 2011...