Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Always use side handle. Tighten the handle securely. The
•
side handle should always be used to maintain control of the
tool at all times.
•
Avoid bouncing the diamond wheel or giving it rough
treatment. If this occurs, stop the tool and inspect the wheel
for cracks or flaws.
•
Do not attempt to do curved cutting. Overstressing the
diamond wheel increases the loading and susceptibility to
twisting or binding of the diamond wheel in the cut and the
possibility of kickback or wheel breakage, which can lead to
serious injury.
•
Always handle and store wheels in a careful manner.
•
Never cut into area that may contain electrical wiring or
piping. Serious injury may result.
•
DO NOT cut metal with a diamond wheel.
•
DO NOT use abrasive wheels.
•
ALWAYS use with a dust collector.
•
Do not operate this tool for long periods of time.
Vibration caused by the operating action of this tool may
cause permanent injury to fingers, hands, and arms. Use
gloves to provide extra cushion, take frequent rest periods, and
limit daily time of use.
Air vents often cover moving parts and should be
•
avoided. Loose clothes, jewelry or long hair can be caught in
moving parts.
•
Threaded mounting of accessories must match the cut-off tool
spindle thread. For accessories mounted by flanges, the arbor
hole of the accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting hardware
of the power tool will run out of balance, vibrate excessively
and may cause loss of control.
•
The grinding surface of the centre depressed wheels must be
mounted below the plane of the shroud lip. An improperly
mounted wheel that projects through the plane of the shroud
lip cannot be adequately protected.
WARNING: When not in use, place tool on its side on
a stable surface where it will not cause a tripping or
falling hazard. Serious personal injury may result.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
•
Health hazards caused by breathing dust developed when
working in concrete and/or masonry.
SAVE THESE INSTRUCTIONS
Chargers
D
WALT chargers require no adjustment and are designed to be
e
as easy as possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
Your D
WALT charger is double insulated in
e
accordance with EN60335; therefore no earth wire
is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead to the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
Important Safety Instructions for All Battery
Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to Technical Data).
•
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock may result.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only D
WALT rechargeable batteries. Other types of
e
batteries may burst causing personal injury and damage.
CAUTION: Children should be supervised to ensure that
they do not play with the appliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
EngLIsh
WALT
e
; the maximum length
2
33
Werbung
Inhaltsverzeichnis
