3M DBI-SALA Flexiguard M200 Handbuch Seite 10

Base more than 4.0 in. (10.2 cm) above the ground.
2. After setting each Adjustable Foot, verify that the Counterweight Base is level using the Level Indicators (A) on
the Base. The Base must be witihin plus or minus 1° from vertical in both directions of the Base. See Figure 8 for
reference.
3.5 USING THE WHEEL KIT (8530908): After installing the Wheel Kit, it may be used to transport the Jib System. See
Section 2.5 for more information.
1. Turn the handle of the Wheel Jack clockwise until it comes into contact with the ground and raises the Base off the
ground. Do not raise the Base more than 2.0 in. (51 mm) off the ground.
2. Use the Leveling Indicators (A) located on the Counterweight Base to verify whether the Base is level. The Base may
be transported after the Base has been determined to be level. See Figure 8 for reference.
;
Do not transport the system on uneven ground. A sloped or uneven surface could cause a loss of control.
3.6 SAFE WORKING RADIUS: The user must stay within the Safe Working Radius (A) of the Jib Boom and must not pass
the end of the rail. The user must remain as directly below the Connection Eye as possible. See Figure 9 for reference.
Leaving the Safe Working Radius to an Outside Location (B) is dangerous and could result in serious injury or death.
When working on either side of the M200 Jib System, keep the anchor point as close overhead as possible. If a rotation
stop is in place on the jib mount, never work past that rotation stop. See the User Instructions for the M200 Jib Boom
(5908372) for more information.
4.0 INSPECTION:
;
After equipment has been removed from service, it may not be returned to service until an Authorized 3M
Representative has inspected the system and has confirmed in writing that it is acceptable to do so.
4.1 INSPECTION FREQUENCY: The Counterweight Base shall be inspected by the user before each use, and additionally
by a Competent Person other than the user at intervals of no longer than one year. A higher frequency of equipment use
and harsher conditions may require increasing the frequency of Competent Person inspections. The frequency of these
inspections should be determined by the Competent Person per the specific conditions of the worksite.
4.2 INSPECTION PROCEDURES: Inspect this product per the procedures listed in the "Inspection and Maintenance Log".
Documentation of each inspection should be maintained by the owner of this equipment. An inspection and maintenance
log should be placed near the product or be otherwise easily accessible to users. It is recommended that the product is
marked with the date of next or last inspection.
4.3 DEFECTS: If the Counterweight Base cannot be returned to service because of an existing defect or unsafe condition,
then either destroy the system or contact 3M or a 3M-authorized service center about possible repair.
4.4 PRODUCT LIFE: The functional life of the Counterweight Base is determined by work conditions and maintenance. As
long as the product passes inspection criteria, it may remain in service.
5.0 MAINTENANCE, SERVICE, and STORAGE
5.1 CLEANING: Periodically clean the metal components of the Counterweight Base with a soft brush, warm water, and a
mild soap solution. Ensure parts are thoroughly rinsed with clean water.
5.2 SERVICE: Only 3M or parties authorized in writing by 3M may make repairs to this equipment.
5.3 STORAGE: If applicable, store the Counterweight Base and associated Fall Protection equipment in a cool, dry, clean
environment out of direct sunlight. Avoid areas where chemical vapors may exist. Thoroughly inspect components after
extended storage.
6.0 LABELS and MARKINGS:
6.1 LABELS: Figure 12 illustrates labels present on the Counterweight Base. Labels must be replaced if they are not present
or fully legible. Information provided on each label is as follows:
1) Do not use the Counterweight Base without the counterweight attached.
A
2) Use of the Counterweight Base with Jib Boom is approved only with the counterweight attached.
1) Notified Body and Applicable Standards
2) Read all instructions.
3) Company Logo
4) Applicable Standards
B 5) Warning Instructions
6) Weight of each Counterweight Box: 5,000 lb. (2,268 kg)
7) Weight of base stand = 1,325 lb. (601 kg)
8) Weight of M200 Jib Boom = ≤1,343 lb. (609 kg)
9) Weight of Counterweight Boxes + M200 Jib Boom = ≤12,668 lb. (5,746 kg)
1) Manufactured (Year/Month)
2) Model Number
C
3) Serial Number
4) Company Logo
10