Specifications; Replacement Parts - Fluke T5-600 Handbuch

Auto Off
45 min
LO
Do not
overtighten
+ 2 AA
screw
+
OFF
Warning
• Disconnect test leads from power source
before opening battery door.
• Débranchez les cordons d'essai avant
d'ouvrir le couvercle de la pile.
• Prima di aprire lo sportello del vano della pila,
scollegare i cavetti dal circuito di
alimentazione.
• Die Prüfleiter vor dem Öffnen des
Batteriefachs von der Stromquelle trennen.
Desconecte los conductores de prueba de la
•
fuente de alimentación antes de abrir la
cubierta de la batería.
• Antes de abrir a tampa do compartimento das
pilhas, desconecte os terminais de teste da
fonte de alimentação.
• Maak de meetkabels los van de stroombron
voordat u de batterijklep opent.
• Koble prøveledningene fra strømkilden før
batteridekselet åpnes.
• Søgeledningerne skal tages evt. emne, inden
batteridækslet åbnes.
• Irrota koestusjohtimet virtalähteestä ennen
paristolokeron avaamista.
•
Koppla bort mätsladdarna från strömkällan
innan du öppnar batteriluckan.
•
•
•
•
•

Specifications

Specifications subject to change without notice.
Calibration 1-year calibration cycle
Temperature
Operating: -10 °C to +50 °C (14 °F to 122 °F)
Storage: -30 °C to +60 °C (-22 °F to +140 °F)
Altitude
Operating: 2000 m (6562 ft)
Storage: 10,000 m (32808 ft)
Relative 0 % to 95 %, 5 ° C to 30 ° C
Humidity (41 ° F to 86 ° F); 0 % to 75 %,
30 ° C to 40 ° C
(86 ° F to 104 ° F); 0 % to 45 %,
40 ° C to 50 ° C
(104 ° F to 122 ° F)
Battery Type AA (2); 360 hours continuous with
and Life alkaline; 125 hours continuous with
zinc chloride
RF Field 0.5 % full scale + (specified accuracy)
Specification at 3 V / m
Enclosure IP 52 per IEC 60529, no vacuum
Rating applied
Safety Complies with ANSI/ISA-S82.01-94,
UL classified to IEC 61010, CSA/CAN
C22.2 No.1010.1-92, and EN 61010-
1: 1995.
EMC EN 61326
Temperature 0.1 x (specified accuracy) / ° C for <18
coefficient ° C or >28 ° C (< 64.4 ° F or > 82.4 ° F)
± ( [ % of reading] + [number of least
Accuracy
significant digits] )
Accuracy is specified for 1 year after
calibration, at 18 ° C to 28 ° C
(64 ° F to 82 ° F) with relative humidity
to 90 %. AC conversions are ac-
coupled, average responding, and
calibrated to the rms value of a sine
wave input.
CAT III protects against transients in a fixed equipment
installation such as a distribution panel, and lighting
systems in large buildings.
CAT IV protects against transients from a primary supply
such as an electricity meter or an overhead or
underground utility service.
Function T5-600 T5-1000 Reso- Accuracy
Range Range lution
600 V 1000 V 1 V ± (1.5 % + 2
rms rms digits)
600 V 1000 V 1 V ± (1 % + 1 digit)
100.0 A 100.0 A 0.1 A ± (3 % + 3 digits)
1000 V CAT III
600 V CAT IV
1000 Ω 1000 Ω 1 Ω ± (1 % + 2 digits)
Certifications:
In accordance with
IEC 61010-1, 54CJ

Replacement Parts

Test Lead Assembly. PN 648029
Replace only with Fluke double-insulated
leads ( ) See "Accessories" for available
probes.
B t a e t y r D o r o PN 2091779
B t a e t y r D o r o S c e r w P N
Accessories
H5 Belt Holster
TP1 Probe Set, Flat-Blade
AC285 SureGrip™ Alligator Clips
AC220 SureGrip™ Alligator Clips
Service Information Sheet, PN 686953
To contact Fluke, call:
USA: 1-888-99-FLUKE (1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-446-5500
Visit Fluke's Web site at www.fluke.com.
1 6 1 8 5 7 8