Upright LX Serie Betriebsanleitung Seite 9

Routine Service
Use the following table as a guide for routine
maintenance. Inspection and maintenance shall
be performed by personnel who are trained and
familiar with mechanical and electrical proce-
dures. Refer to the Service Manual for complete
service instructions.
Please copy this page and use the Routine Service
Table as a checklist when inspecting a machine for
service.
COMPONENT INSPECTION OR SERVICES
Engine Oil Check level and condition
Check for leaks
Change oil & filter (Dual Fuel)
Change oil & filter (Diesel)
Engine Fuel Check fuel level
System Check for leaks
Replace fuel filter
Check air cleaner
Engine Check electrolyte level
Battery Check specific gravity
System Clean exterior
Check battery cable condition
Clean terminals
Engine Check coolant level (with engine cold)
Coolant Replace coolant
Hydraulic Check oil level
Oil Change filter
Drain and replace oil
Hydraulic Check for leaks
System Check hose connections
Check hoses for exterior wear
Emergency Open the emergency lowering
Hydraulic valve and check for
System serviceability
Controller Check switch operation
Control Check the exterior of the cable
Cable for pinching, binding or wear
Platform Check fasteners for proper torque
Deck and Check welds for cracks
Rails Check condition of deck
Tires Check for damage
Check air pressure (50psi)
Check lug nuts (torque to 90 ft. lbs. [123 Nm])
Hydraulic Wipe clean
Pump Check for leaks at mating surfaces
Check for hose fitting leaks
Check mounting bolts for proper torque
Drive Motors Check for operation and leaks
Steering Check hardware & fittings
System for proper torque
Oil all pivot points
Check steering cylinder for leaks &
mounting bolts for proper torque
Downloaded from www.Manualslib.com
Routine Service Table
INTERVAL Y N R
Daily
Daily
30
100
HOURS
Daily
Daily
6
Daily
Daily
30
6
Daily
6
Daily
3
Daily
6
2
Daily
30
30
Daily
Daily
Daily
Daily
Daily
Daily
Daily
Daily
30
30
30
Daily
30
Daily
6
30
30
manuals search engine
Routine Service Table Key
Interval
Daily=each shift (every day) or every eight hours
30d=every month (30 days) or every 50 hours
3m=every 3 months or 125 hours
6m=every 6 months or 250 hours
1y=every year or 500 hours
2y=every 2 years or 1000 hours
Y=Yes/Acceptable
N=No/Not Acceptable
R=Repaired/Acceptable
COMPONENT INSPECTION OR SERVICES
Elevating Inspect for structural cracks
Assembly Check pivot points for wear
Check pivot pin mounting bolts
D
for proper torque
Check scissor arms for bending
Grease scissor pins
Chassis Check hoses for pinch or
M
rubbing points
Check component mounting
for proper torque
D
Check welds for cracks
M
Lift Check the cylinder rod for wear
Cylinder Check pivot pin mounting bolts
M
for proper torque
Check seals for leaks
M
Inspect pivot points for wear
Check fittings for proper torque
M
Axle Check the cylinder rod for wear
Y
Cylinder Check mounting pin pivot bolts
for proper torque
D
Check seals for leaks
D
Inspect pivot points for wear
Check fittings for proper torque
Entire Check for and repair
Unit collision damage
Check fasteners for proper torque
Check for corrosion-remove
and repaint
Lubricate
Labels Check for peeling, missing, or unreadable
labels & replace
D
D
D
D
M
Service Report
D
D
Date: _______________
Owner: ___________________________________
Model No: _____________ Serial No: __________
Serviced By: _______________________________
Service Interval: ____________________________
9
INTERVAL Y N R
Daily
30
D
30
D
6
M
30
D
Daily
6
M
Daily
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
Daily
3
M
6
M
30
D
Daily