EINHELL PICOBELLA Originalbetriebsanleitung Seite 26

than for reaching the full speed – risk of injury!
•
Never use the equipment for too long at any
one point.
•
We recommend wet cleaning. Only use clean
water without any additives whatsoever.
•
Keep your hands and feet away from the rota-
ting brush.
•
Only insert the battery just before you start
your work and remove it again when you have
finished.
6.1 Changeover switch (Fig. 18)
Note:
•
Using the changeover switch you can select
the direction of rotation of the equipment and
lock it so that it cannot be switched on acci-
dentally. You can select between forward and
reverse rotation. Forward is the standard di-
rection of rotation, with which the equipment
has the most power.
•
Hold the equipment firmly by the handle and
additional handle and make sure you have a
steady standing position.
•
To avoid causing damage to the equipment,
the direction of rotation must only be changed
when the equipment is at a standstill.
a) Forward (standard direction of rotation):
Slide switch on left (V) pressed - the equip-
ment pulls away from you.
b) Safety- lock-off : Slide switch in the middle
position (as shown) - On/Off switch blocked
c) Reverse: Slide switch on right (R) pressed -
the equipment moves towards you.
6.2 On/Off switch (Fig. 15 / Item 3)
a) Switching on
When you press the On/Off switch, the brush
rotates.
b) Switching off
When you release the On/Off switch, the
equipment switches off and the brush comes
to a standstill.
6.3 Speed controller (Fig. 18 / Item 4)
To set the speed of the brush, turn the speed con-
troller (min = lowest / max = highest). This allows
the speed to be adjusted to the particular surface
being cleaned. The numbers 1 – 5 marked on the
speed controller are provided to indicate the set
speed more clearly.
Anl_Picobella_SPK7.indb 26 Anl_Picobella_SPK7.indb 26
GB
6.4 Operation
Note: Worn or frayed brushes should be replaced
in good time. Replace the brush as soon as its
diameter is less than approx. 95 mm. A brush dia-
meter of any less can lead to damage.
Important! If the permissible input current is ex-
ceeded (e.g. by pressing too strongly), the equip-
ment switches off automatically and must be swit-
ched on again by pressing the On/Off switch.
6.4.1 Cleaning in general (not applicable to
section "6.4.5 Brushing artifi cial turf")
1. Place the brush evenly on the surface.
2. Set the working height to the one which is
most comfortable for you (see section 5.3).
The splash guard (Fig. 1 / Item 14) must just
clear the ground on both sides.
3. Select the correct direction of rotation (see
section 6.1) for the surface you want to clean
(observe sections 6.4.2 – 6.4.4).
4. To achieve top cleaning results quickly, we re-
commend wet cleaning. Open the water inlet.
5. Lift the equipment 1-2 centimeters and switch
on the equipment (see section 6.2).
6. Set the desired speed (from slow to fast) (see
section 6.3). Wait until the full speed has been
reached and then place the brush on the sur-
face to be cleaned.
7. Guide the brush slowly and in lines, similar to
a broom, over the surface. Only apply a small
amount of pressure at fi rst and then increase
it little by little.
6.4.2 Cleaning wood, composite materials
(BPC/WPC)
Warning! Use only the SOFT brush to do this (to
fi t the brush, see section 5.5). All other available
brushes are made of hard material and can da-
mage the surface.
•
Always clean the boards or wooden elements
in a longitudinal direction (along the grain).
•
Actuate the left side (Fig. 18 / Item V) of the
changeover switch (forward). The equipment
will pull away from you (standard direction of
rotation).
•
It is recommended that you clean on a board-
by-board basis.
•
Afterwards, rinse the cleaned surface down
with water.
- 26 -
24.10.2019 07:44:13 24.10.2019 07:44:13