Before Starting The Equipment - EINHELL PICOBELLA Originalbetriebsanleitung

Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger.
5.1 Turn the steady grip out of the transport
position (Fig. 3-4)
Important! For transport reasons the steady grip
is turned 90° to the side. For you to be able to
work with the equipment, the steady grip must be
aligned in line with the brush housing (working
position).
1. Slacken the lock nut (8) by turning it counter-
clockwise and turn the steady grip as far as it
will go.
2. Secure the lock nut (8) by turning it clockwise.
5.2 Fitting the additional handle (Fig. 5)
Using the handle screws (6), fasten the additio-
nal handle (B) (the screws are accessible from
below) and the holder (C) at the area provided.
5.3 Adjusting the length of the long handle
(Fig. 6)
To ensure that you have a comfortable working
position, the length of the long handle can be
adjusted.
1. Slacken the lock nut (8) by turning it counter-
clockwise.
2. To change the length of the long handle, pull
the long handle (9) out of the steady grip (D)
or push it into the steady grip.
3. Make sure that the steady grip is in the wor-
king position (section 5.1) and secure the
lock nut (8) by turning it clockwise.
5.4 Adjusting the additional handle (Fig. 5)
Undo the two fastening screws (6) on the additi-
onal handle until it can be moved in any direction
without any great resistance. Set the required
position and tighten the two fastening screws (6)
again.
Anl_Picobella_SPK7.indb 24 Anl_Picobella_SPK7.indb 24
GB
5.5 Fitting the cleaning brushes (Fig. 7-10)
Remove the brush covers on the sides (Fig. 7 /
Item 13). The product is supplied complete with
a 2-piece SOFT nylon brush (yellow/green). The
cleaning brushes have rubber caps (Fig. 8 / Item
G) on the outside. Slot one nylon brush onto the
left side of the brush mount and the second nylon
brush onto to the right side of the brush mount
(Fig. 9). Fit the brush covers back in place. The
SOFT nylon brush is now fi tted (Fig. 10).
The MEDIUM nylon brush (black) is equipped
with a side brush. Slot the nylon brush with side
brush onto the brush mount on either the left or
right side according to your requirements and the
other nylon brush onto the other brush mount.
Also included with the PICOBELLA is a wide
brush cover which must be used for the nylon
brush with side brush. Fit the brush covers back
in place. The MEDIUM nylon brush is now fi tted
(Fig. 10a).
The ULTRA metal brush (Fig. 10b) must be fi tted
in the same way.
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
5.6 Removing cleaning brushes
Remove the brush covers on the sides (Fig. 7 /
Item 13). Press the middle of the rubber cap (Fig.
11 / Item G) to actuate the release button under-
neath and pull off the brush at the same time.
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
5.7 Water inlet connector (Fig. 12 – 14b)
To achieve top cleaning results quickly, we recom-
mend wet cleaning.
Important!
•
Observe the requirements of EN 1717 in rela-
tion to the connection of the water connection
to the drinking water network. Consult a spe-
cialist plumbing company.
•
Never direct the water jet at electric cables or
the equipment itself.
•
The water temperature must be between
+5°C and +35°C.
•
Do not use water that is dirty, gritty or con-
tains any chemical products, as these could
impair operation and shorten the life of the
equipment.
- 24 -
24.10.2019 07:44:13 24.10.2019 07:44:13