STEINEL PROFESSIONAL IS 2300 ECO Montageanleitung Seite 9

Installing IS 2300 ECO
screwed to the wall after
L black
feeding the cables through.
N blue
Connecting the power
L'
brown
supply lead
The mains power lead and
Wall mounting
load supply lead are
The site of installation should
2 to 3-core cables:
be at least 50 cm away from
L, L' = live conductor or
a light because heat radiated
from it may activate the system.
The motion detector should
be mounted at a height of
N = neutral conductor
approx. 2 m.
Using a screwdriver, undo
PE = any protective
the fi xing screw by turning it
clockwise and slide the
mounting plate down and off.
If you are in any doubt,
Fit the rubber plug provided
identify the conductors using a
into the mounting plate. Hold
voltage tester; then disconnect
the mounting plate against the
from the power supply again.
wall and mark where to drill
The mains and load conductors
the holes, paying attention to
must be wired up using the con-
any wiring already existing in
necting terminals provided:
the wall, drill holes; insert wall
1. Fit the live conductor (L) into
plugs.
the fi rst terminal.
For the motion detector to
2. Fit the neutral conductor (N)
trigger a load, the mains power
into the second terminal.
must be fed in by at least a
3. Fit the switched phase to the
two-core cable and on to the
load (L') into the third terminal.
load by a second cable. To do
4. A suitable screw-type or plug-
this, the two rubber plugs can
in terminal rated for at least 300V
be pierced with a screwdriver.
with a terminal cross section of
Two tabs are provided at the
at least 2.5mm² must be used
base of the wall mount for
for wiring through the protective-
surface wiring. These can
earth conductor.
easily be snapped off. The
mounting plate can be
Important:
Getting the cable connections
crossed will produce a short
circuit in the unit or in your
fuse box. In this case, you
must check the identifi cation
of all cables and re-connect
them. A mains switch for
switching the light 'ON' and
phase to the load 'OFF' can of course be in-
(usually black or stalled in the mains lead.
brown)
(mostly blue)
earth ( )
16
Function
The system can be put into motion detector and attaching
operation after connecting the it to the wall mount. Two setting
Switch-off delay
(time setting)
The desired duration of
illumination of the connected
lamp is infi nitely adjustable
between approx. 10 sec.
to a maximum of 15 min.
Control dial set to 1 =
minimum duration.
Control dial set to 6 =
approx. 10 sec. - 15 min. max.
maximum duration.
Twilight setting
The motion detector's response
threshold can be infi nitely var-
ied from approx. 2 to 2000 lux.
Control dial set to 1 =
daylight operation.
Control dial set to 6 =
night-time operation.
(The IS 2300 ECO leaves the
factory set to daylight
2 - 2000 lux
operation.)
Reach setting/adjustment
At an assumed mounting housing can also be turned
height of 2 m, the maximum through ± 80°
reach of the sensor is 12 m. targeting. The shroud can be
The detection zone setting separated along the pre-
can be optimised to suit re- grooved divisions in the verti-
quirements. The shrouds sup- cal and horizontal directions
plied with the sensor can be or cut with scissors
used to mask out as many removing the decorative ring
lens segments as you wish or the shrouds can be clipped
shorten reach to suit the par- on at the top of the sensor
ticular situation. The sensor lens.
A B
options are provided after de-
taching the decorative ring.
(The IS 2300 ECO leaves the
factory set to the shortest
time).
The shortest time setting is
recommended when adjusting
the detection zone.
When setting the motion
detector for the detection
zone, the control dial must be
set to 1 = daylight operation.
Dazzle guard: This product
is equipped with an integrat-
ed dazzle guard. If blinded
by extraneous light, this puts
the sensor into a brightness-
related evaluation mode for
60 sec. (cf. Troubleshooting).
The decorative ring must now
for precision be pushed back on to hold the
shrouds fi rmly in place. This
prevents the light from being
activated unintentionally, e.g.
by cars, passers-by etc. and
. After allows you to target danger
spots.
C
17