Specifications - Makita RT0700CX3J Betriebsanleitung

ENGLISH
(Original instructions)
1 Bit protrusion
2 Tool base
3 Scale
4 Locking lever
5 Adjusting screw
6 Hex nut
7 Switch
8 OFF (O) side
9 ON ( I ) side
10 Speed adjusting dial
11 Tighten
12 Loosen
13 Hold
14 Shaft lock
15 Workpiece
16 Bit revolving direction
17 View from the top of the tool
18 Feed direction
19 Straight guide
20 Thumb nut
21 Base protector
22 Screws
23 Screwdriver
24 Straight bit
25 Base
26 Templet
27 Distance (X)
28 Templet guide 10

SPECIFICATIONS

Model
Collet chuck capacity.................6 mm, 8 mm, 1/4" or 3/8"
-1
No load speed (min ) ............................ 10,000 – 30,000
Overall length ...................................................... 200 mm
Net weight .............................................................. 1.8 kg
Safety class .............................................................
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
12
Explanation of general view
29 Base protector
30 Bolt
31 Guide plate
32 Wing nut
33 Clamp screw (A)
34 Center hole
35 Nail
36 Clamp screw (A)
37 Adjusting screw
38 Clamp screw (B)
39 Trimmer guide
40 Bit
41 Guide roller
42 Clamping screws
43 Base protector
44 Screw
45 Pulley
46 Collet nut
47 Collet cone
48 Wrench
49 Belt
50 Locking lever
51 Offset base
52 Hex wrench
53 Offset base plate
54 Upper section of the offset base
55 Bar type grip (optional acces-
sory)
General Power Tool Safety Warnings
RT0700C
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
/II
Save all warnings and instructions for future refer-
ence.
TRIMMER SAFETY WARNINGS
1.
ENE010-1
2.
ENF002-1
3.
4.
5.
6.
7.
8.
9.
56 Grip attachment (optional
accessory)
57 Trimmer base
58 Knob type grip
59 Plunge base
60 Grip
61 Knob
62 Adjusting knob
63 Lock lever
64 Depth pointer
65 Stopper pole setting nut
66 Fast-feed button
67 Stopper pole
68 Stopper block
69 Adjusting bolt
70 Guide holder
71 Wing bolts
72 Guide bar
73 Wing bolt
74 Outside diameter of the templet
guide
75 Templet guide
76 Dust nozzle
77 Thumb screw
78 Limit mark
79 Brush holder cap
WARNING Read all safety warnings and all
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
Wear hearing protection during extended period
of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
GEA010-1
GEB019-4