Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SPECIAL SETTINGS
Searching for digital television
channels from a satellite manu-
ally
If you know the parameters of a new television
channel, you can also search for it manually.
Current transponder data can be found in the
teletext, in satellite TV magazines or on the
Internet.
1
Open the menu with »M«.
2
Select the line »SOURCE SETUP« with
»D«
or
and press »OK« to confirm.
– The »SOURCE SETUP« menu appears.
3
Select »Digital Manual Tuning « with
»D«
and press »OK« to confirm.
– The menu appears.
4
Select the line required for the parameters
»C«
»D«.
with
or
– »Frequency (MHz)«: Enter the five-digit
frequency with
– »Symbol Rate (kS/s)«: Enter the five-digit
symbol rate with
– »Polarization«: Use
polarisation to »Horizontal« or »Vertical«.
– »Network Search«: use
lect the option »On« or »Off«.
– »Scan Mode«: Use
whether you want to search for unencrypt-
ed (Unencrypted) channels only, encrypt-
ed (Encrypted) channels only, or for both
(Unencrypted + Encrypted).
– »Service Type«: Use
whether you want to search for television
channels only (TV), radio stations only
(Radio), or both (Radio + TV).
5
Start the scan with » « (red).
– The »Results« menu appears, and the scan
for TV channels begins.
Note:
You can abort the search by pressing »
7
M
6
Press »
« to end the setting.
46
ENGLISH
----------------------------------------------------------------------------------------------------------
»C«
»1 ...
0« .
»1 ...
0« .
»
B
«
»
A
«
or
to set the
»
B
«
»
A
«
or
»
B
«
»
A
«
or
to select
»
B
«
»
A
«
or
to select
LNB settings
Notes:
The following description about the LNB
7
settings premise a substantial expertise
about the satellite systems. Ask your
specialist dealer.
Your TV supports SCR system (Satellite
7
Channel Router). If you are using SCR
satellite system, follow the steps described
in »LNB Type« section.
»C«
1
Open the menu with »M«.
2
Select the line »SOURCE SETUP« with
»D«
or
or
– The »SOURCE SETUP« menu appears.
3
Select »Antenna Settings« with
and press »OK« to confirm.
– The »ANTENNA SETTINGS« menu ap-
pears.
4
Select the line required for the parameters
»C«
with
– »Satellite«: »Press OK«, select a satellite
»
with
»OK« to confirm.
– »Transponder«: »Press OK«, select a tran-
to se-
sponder with
and press » « to confirm. Use » « (red)
to add a transponder, use » « (green) to
delete it, or use » « (yellow) to change
transponder data.
– »LNB Power«: Set the LNB power supply
(depending on the type of LNB) to »Off«
»13/18 V« or »14/19 V« with
»
A
«.
– »LNB Type«: Select the LNB type used in
the satellite system with »
you are using a satellite antenna with an
Single Cable Distribution multiswitch, select
the setting »Grundig SCR«. After it, please
perform the »User Band«, »KB Frequency«
and »LNB Selection« settings in the
M
«.
submenus. The necessary parameters you
will get from the operator of the satellite
antenna. Use only this specification!
»User Band«: Select the user band
number assigned to the user with »
or »
and press »OK« to confirm.
»D«
or
.
«
»
«
»C«
»D«
B
A
,
,
or
»
B
«
»
A
«
,
,
B
« or »
A
«.
»C«
»C«
»D«
or
and press
»C«
»D«
or
»
B
«
or
A
«. If
B
«
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
