Loading Staples - Makita ST113D Betriebsanleitung

ASSEMBLY
CAUTION:
Always make sure that the battery
cartridge is removed before carrying out any work
on the stapler.
Staples
CAUTION:
Do not use staples other than
designated in this manual or staples that appear
to be damaged, bent, rusty or corroded.
CAUTION:
Load the same type, size and
uniform length of staples when loading multiple
strips of staples in the magazine.
NOTICE:
Handle the staples and their box carefully.
If the staples have been handled roughly, they may be
bent out of shape, causing poor staple feed or jamming.
NOTICE:
Avoid storing the staples in a very humid
or hot place or place exposed to direct sunlight.

Loading staples

WARNING:
When loading staples, always
make sure that the battery cartridge is removed
from the stapler. Unintentional firing may cause
personal injuries and property damage.
CAUTION:
After loading staples, make sure
that the sub magazine is surely closed. F alling
staples out of the magazine may cause an injury to
t h e operator or b y stan d er, espe c iall y w h en w orking in
h ig h lo c ations.
1.
R emo v e t h e batter y c artri d ge.
2. P ress t h e lo c king le v er an d sli d e t h e sub maga-
z ine ba c k w ar d .
► Fig.6: 1. L o c king le v er 2. S ub maga z ine
3. L oa d staples into t h e main maga z ine w it h t h eir
f eet f a c ing up.
► Fig.7: 1. S taples 2. Main maga z ine
4.
A f ter loa d ing staples, pus h ba c k t h e sub-maga-
z ine in pla c e until it c li c ks.
T o remo v e staples, f ollo w t h e installation pro c e d ures in
re v erse.
Hook
CAUTION:
Do not hang the hook from the
waist belt. D ropping t h e stapler, w h i c h is c ause d b y
t h e h ook a c c i d entall y c oming out o f pla c e, ma y c ause
unintentional firing and result in personal injuries.
► Fig.8
T h e h ook is c on v enient f or temporaril y h anging t h e tool.
T h is c an be installe d on eit h er si d e o f t h e tool.
T o install t h e h ook, insert it into a groo v e in t h e tool
h ousing on eit h er si d e an d t h en se c ure it w it h a s c re w .
T o remo v e, loosen t h e s c re w an d t h en take it out.
► Fig.9: 1. G roo v e 2. H ook 3. S c re w
OPERATION
Testing the safety system
WARNING:
Make sure all safety systems are
in working order before operation. Failure to do
so may cause personal injuries.
► Fig.10: 1. T rigger-lo c k button 2. S w it c h trigger
3. C onta c t element 4. S ub maga z ine
T est sa f et y s y stems f or possible f ault be f ore operation
as f ollo w s.
1. U nloa d staples f rom t h e tool an d keep t h e sub
maga z ine opene d .
2. I nstall t h e batter y c artri d ge.
3. O nl y pull t h e s w it c h trigger w it h out tou c h ing t h e
c onta c t element against t h e material.
4. O nl y tou c h t h e c onta c t element against t h e mate-
rial w it h out pulling t h e s w it c h trigger.
I f t h e tool operates in t h e c ase o f 3 an d 4 abo v e, t h e
sa f et y s y stems are f ault y . S top using t h e tool imme d i-
atel y an d ask y our lo c al ser v i c e c enter.
Driving staples
WARNING:
Continue to place the contact
element firmly on the material until the staple is
driven completely. Unintentional firing may cause
personal injuries.
► Fig.11: 1. S w it c h trigger 2. C onta c t element 3. F ront
part 4. R ear part
Y ou c an operate t h e tool in eit h er w a y o f " single
se q uential a c tuation " or " c onta c t a c tuation " .
Single sequential actuation:
I n t h is mo d e, y ou c an d ri v e one staple b y one se q uen-
tial operation.
1. Place flat the contact element on the material.
2.
H ol d bot h o f t h e f ront part an d t h e rear part o f t h e
tool firmly against the material.
3. P ull t h e s w it c h trigger f ull y to d ri v e t h e staples.
4. Release your finger from the switch trigger before
mo v e t h e c onta c t element f rom t h e material.
Contact actuation:
I n t h is mo d e, y ou c an d ri v e staples se q uentiall y .
1.
P ull t h e s w it c h trigger.
2. With the switch trigger pulled, place flat the con-
ta c t element on t h e material to d ri v e t h e staples.
3. Move the tool to the next area and place flat the
c onta c t element on t h e material again.
NOTE: T h e groo v e in d i c ates t h e point t h at staple is
d ri v en.
► Fig.12: 1. G roo v e
I f t h e h ea d o f t h e staple remains abo v e t h e w orkpie c e
sur f a c e, d ri v e t h e staple w h ile h ol d ing t h e stapler h ea d
firmly against the workpiece.
► Fig.13
7 ENGLISH