Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
•
During the operation or between the opera-
tion cycles, you can add the required ingre-
dients into the bowl (3). To do this, turn the
measuring cup (1) counterclockwise and
remove it. After adding ingredients through
the lid (2) opening, install the measuring cup
(1) back to its place.
•
After the unit operation is finished, set the
operation mode switch (7) to the «0» posi-
tion and unplug the unit.
•
Remove the blender bowl (3) from the motor
unit (6) by turning it counterclockwise (the
symbol
on the blender bowl should be
above the symbol
•
Remove the lid (2) from the bowl (3) holding
the base of the measuring cup (1).
•
Remove the measuring cup (1) from the lid
(2), turning it counterclockwise.
•
Take the processed products out of the bowl
(3). If necessary, you can use a spatula to
remove the products.
•
After the operation is finished, wash the
blender bowl (3).
Note:
If food processing is hindered, you can add
–
some water, liquor or juice into the blender
bowl.
ATTENTION! Continuous operation time of
the blender should not exceed 3 minutes;
then switch the unit off and let it cool down
to room temperature for at least 10 min-
utes.
CLEANING AND CARE
After the unit operation is finished, switch the
blender off by setting the operation mode
switch (7) to the «0» position and unplug it,
remove the blender bowl (3) from the motor
unit (6) as described in the section «USING THE
BLENDER». Remove the processed food from
the bowl (3).
•
Wash the bowl (3) preliminarily. To do this
place the blender bowl (3) on the motor
unit (6) and turn it clockwise until it is fixed
(the symbol
on the blender bowl should
be above the symbol
Add some soap solution into the bowl (3).
Cover the bowl (3) with the lid (2) with
installed measuring cup (1). Insert the
power plug into the mains socket. Set the
switch (7) to the position «P» and hold it for
several seconds. After that set the opera-
IM VT-8513.indd 5
on the motor unit).
on the motor unit).
5
tion mode switch (7) to the position «0» and
unplug the unit.
•
Remove the blender bowl (3) from the motor
unit (6) by turning it counterclockwise (the
symbol
on the blender bowl should be
above the symbol
•
Remove the lid (2) from the bowl (3) holding
the base of the measuring cup (1).
•
Remove the measuring cup (1) from the lid
(2), turning it counterclockwise.
•
Pour out the soap solution from the bowl (3)
and rinse the bowl (3).
•
Turn over the bowl (3) and turn the knife
block (5) clockwise in the direction of
«OPEN» arrow as far as it will go (pic. 4).
Remove the knife block (5) from the bowl (3)
(pic. 5). Remove the sealing gasket (4) from
the knife block.
ATTENTION: The cutting edges of the
knives are very sharp and dangerous.
Handle them very carefully.
•
Wash the measuring cup (1), the lid (2), the
bowl (3), the sealing gasket (4) and the knife
block (5) with warm water, at temperature
not exceeding +70°С, adding soft detergent
and then dry them.
•
Clean the unit body with a soft damp cloth
and then wipe it dry.
•
Do not use coarse sponges, abrasives and
solvents to clean the blender.
•
Do not immerse the blender motor unit (6)
and the knife block (5) into any liquids; do
not wash it in a dishwashing machine.
•
Do not put the removable parts of the
blender in a dishwashing machine as well.
•
Set the sealing gasket (4) on the knife
block (5).
•
Install the knife block (5) into the blender
bowl (3). Turn the knife block (5) counter-
clockwise in the direction of «CLOSE» arrow
as far as it will go (pic. 1).
Note:
•
To avoid damage of the sealing gasket (4)
when installing the knife block (5), do not
apply excessive effort.
STORAGE
•
Perform the requirements of the CLEANING
AND CARE section before taking the unit
away for storage.
•
Keep the unit away from children in a clean
and dry place.
ENGLISH
on the motor unit).
25.04.2016 10:02:10
Werbung
Inhaltsverzeichnis
