Operation - EINHELL TE-ID 750/1 E Originalbetriebsanleitung

5.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
Undo the thumb screw (a) on the additional
n
handle (8) and insert the depth stop (2) in the
hole of the additional handle.
Set the depth stop and retighten the thumb screw.
n
Now drill the hole until the depth stop touches the
n
workpiece.
5.3 Fitting the drill bit (Fig. 5)
Always pull the power plug before making
n
adjustments to the equipment.
This hammer drill is equipped with a spindle lock
n
(9) and a quick-change drill chuck.
Press the spindle lock (9) and turn the drill chuck
n
(1) until it engages. Keeping the spindle lock (9)
pressed, turn the firmly closed drill chuck (1) so
that it opens. The drill chuck opening must be
large enough to take the drill bit.
Select a suitable drill bit. Push the drill bit as far as
n
possible into the chuck opening.
Keeping the spindle lock (9) pressed, turn the drill
n
chuck (1) so that it closes. Check that the drill bit
is secure in the chuck (1).
Check at regular intervals that the drill bit or tool is
n
secure (pull the mains plug).
When the quick-change drill chuck (1) is open as
n
far as it will go (maximum drill bit opening) and
secure, press the spindle lock (9) and turn the drill
chuck (1) clockwise (viewed from the front) until
you hear a grating noise. Keeping the spindle lock
(9) pressed, turn the drill chuck (1) approx. 5 mm
in the opposite direction until you hear a clicking
noise. Then turn the drill chuck (1) clockwise
again to the desired position. This function will
prevent damage to the drill chuck.
Important.
Do not press the spindle lock (9) while the drill is in
use.

6. Operation

6.1 ON/OFF switch (Fig. 6/Item 5)
First fit a suitable drill bit into the tool (see 5.3).
n
Connect the mains plug to a suitable socket.
n
Position the drill in the position you wish to drill.
n
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
Important. It may only be locked if the drill is set to
rotate clockwise.
To switch off:
Press the ON/OFF switch (5) briefly.
6.2 Adjusting the speed (Fig. 6/Item 5)
n
n
n
n
n
Tip: Start drilling holes at low speed. Then increase
the speed in stages.
Benefits:
n
n
6.3 Preselecting the speed (Fig. 6/Item 6)
n
n
n
6.4 Clockwise/Counter-clockwise switch
n
n
Direction
Clockwise (forwards and drill) Pushed in to the right
Counter-clockwise (reverse)
www.sidirika-nikolaidi.gr
You can infinitely vary the speed whilst using the
tool.
Select the speed by applying a greater or lesser
pressure to the ON/OFF switch (5).
Select the correct speed: The most suitable
speed depends on the workpiece, the type of use
and the drill bit used.
Low pressure on the ON/OFF switch (5): Lower
speed (suitable for: small screws and soft
materials)
Greater pressure on the ON/OFF switch (5):
Higher speed (suitable for large/long screws and
hard materials)
The drill bit is easier to control when starting the
hole and will not slide away.
You avoid drilling messy holes (for example in
tiles).
The speed setting ring (6) enables you to define
the maximum speed. The ON/OFF switch (5) can
only be pressed to the defined maximum speed
setting.
Set the speed using the setting ring (6) on the
ON/OFF switch (5).
Do not attempt to make this setting whilst the drill
is in use.
(Fig. 6/Item 7)
Change switch position only when the drill is
at a standstill!
Switch the direction of the hammer drill using the
clockwise/counter-clockwise switch (7):
GB
Switch position
Pushed in to the left
13