Hander HFS-136 Bedienungsanleitung Seite 2

6
1
2
3
4
English tool (tools with a rating of 230V or 240V can also be
English
• Always disconnect plug from power source before
connected to a 220V supply)
making any adjustment or changing any accessory
● If the drill bit becomes unexpectedly jammed
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
(causing a sudden, dangerous reaction),
Hammer drill • Do not connect the blue (= neutral) or brown (= live)
Finishing sander
immediately switch off the tool
wire in the cord of this tool to the earth terminal of the
plug ● Be aware of the forces that occur as a result of
INTENDED USE
INTENDED USE jamming (especially when drilling metals); always
• If for any reason the old plug is cut off the cord of this
This tool is intended for dry sanding and fi nishing of wood, This tool is intended for hammer drilling in brick,
tool, it must be disposed of safely and not left unattended hold the tool firmly with both hands and take a
concrete and stone as well as for drilling in wood,
painted surfaces, plastic and fi ller • the dust suction requires the use of perforated sanding secure stance
metal, ceramic and plastic. Tools with electronic
sheets ● Always disconnect plug from power source before
TECHNICAL SPECIFICATIONS speed control and left/right rotation are also suitable 1
• perforation in sanding sheet should correspond with making any adjustment or changing any accessory
for screwdriving and thread cutting perforation in sanding foot
● Holding the tool
• replace worn sanding sheets in time
PRODUCT ELEMENTS 2 - keep the ventilation slots uncovered
TECHNICAL SPECIFICATIONS 1 • always use the tool with the total sanding surface
- do not apply too much pressure on the tool; let the
covered with sanding paper
1 On/Off switch tool do the work for you
• before the sanding surface reaches the workpiece, you
2 Switch locking button
PRODUCT ELEMENTS 2
should switch on the tool
Your machine is double insulated in
• before switching off the tool, you should lift it from the
SAFETY
accordance with EN 50144; therefore
1 On/Off switch with speed control
workpiece
WARNING! Read all instructions. Failure to follow all in- no earthwire is required.
2 Switch locking button
• do not apply too much pressure on the tool; let the
structions listed below may result in electric shock, fi re
3 Wheel for maximum speed control
sanding surface do the work for you
and/or serious injury.
MAINTENANCE
4 Switch for changing direction of rotation
5 Switch for selecting drilling function
• Avoid damage that can be caused by screws, nails and
Make sure that the machine is not live
6 Auxiliary handle Your machine is double insulated in accord-
other elements in your workpiece; remove them before
when carrying out maintenance work
ance with EN 50144; therefore no earthwire is
you start working
required. on the motor.
SAFETY
• Always keep the cord away from moving parts of the
WARNING! Read all instructions. Failure to follow
tool; direct the cord to the rear away from the tool
MAINTENANCE Regularly clean the machine housing with a soft
all instructions listed below may result in electric
• When you put away the tool, switch off the motor and
cloth, preferably after each use. Keep the
shock, fire and/or serious injury.
ensure that all moving parts have come to a complete
ventilation slots free from dust and dirt.If the dirt
standstill Make sure that the machine is not live when
does not come off use a soft cloth moistened with
• Use completely unrolled and safe extension cords with ● Wear ear protectors with hammer drills (exposure carrying out maintenance work on the motor.
soapy water. Never use solvents such as petrol,
a capacity of 16Amps (U.K. 13Amps) to noise can cause hearing loss)
Regularly clean the machine housing with a soft cloth, alcohol, ammonia water, etc. These solvents may
• In case of electrical or mechanical malfunction, imme- ● Use auxiliary handles supplied with the tool (loss
diately switch off the tool and disconnect the plug preferably after each use. Keep the ventilation slots free damage the plastic parts.
of control can cause personal injury)
from dust and dirt.If the dirt does not come off use a soft
• SBM Group can assure fl awless functioning of the tool ● Avoid damage that can be caused by screws, The machine requires no additional lubrication.
cloth moistened with soapy water. Never use solvents
only when original accessories are used Should a fault occur, e.g. after wear of a part,
nails and other elements in your workpiece; remove
• This tool should not be used by people under the age such as petrol, alcohol, ammonia water, etc. These sol-
them before you start working please contact your local SBM Group dealer.
of 16 years vents may damage the plastic parts.
● Always keep the cord away from moving parts of
The machine requires no additional lubrication.
• The noise level when working can exceed 85 dB(A);
the tool ENVIRONMENT
wear ear protection Should a fault occur, e.g. after wear of a part, please con-
In order to prevent the machine from damage
● When you put away the tool, switch off the motor
• If the cord is damaged or cut through while working, do tact your local SBM Group dealer.
and ensure that all moving parts have come to a during transport, it is delivered in a sturdy
not touch the cord, but immediately disconnect the plug
packaging. Most of the packaging materials can be
complete standstill
ENVIRONMENT
• Never use tool when cord is damaged; have it replaced
● Use completely unrolled and safe extension cords recycled. Take these materials to the appropriate
by a qualifi ed person In order to prevent the machine from damage during
recycling locations. Take your unwanted machines
with a capacity of 16 Amps (UK 13 Amps)
• Always check that the supply voltage is the same as transport, it is delivered in a sturdy packaging. Most of the
● In case of electrical or mechanical malfunction, to your local SBM Group dealer. Here they will be
the voltage indicated on the nameplate of the tool (tools packaging materials can be recycled. Take these materi-
disposed of in an environmentally safe way.
immediately switch off the tool and disconnect the
with a rating of 230V or 240V can also be connected to a als to the appropriate recycling locations. Take your un-
plug
220V supply) wanted machines to your local SBM Group dealer. Here
● SBM Group can assure flawless functioning of
• This tool is not suitable for wet sanding they will be disposed of in an environmentally safe way.
the tool only when original accessories are used
• Do not work materials containing asbestos (asbestos is
considered carcinogenic) ● Use only accessories with an allowable speed
matching at least the highest no-load speed of the
• When sanding metal, sparks are generated; do not use
dustbox and keep other persons and combustible material tool
from work area ● This tool should not be used by people under the
• Do not touch the moving sanding sheet age of 16 years
• Do not continue to use worn, torn or heavily clogged ● Be careful not to drill or drive into areas where
sanding sheets
electrical wires may be contacted
• Wear protective gloves, safety glasses, close-fi tting
● If the cord is damaged or cut through while
clothes and hair protection (for long hair)
working, do not touch the cord, but immediately
• Take protective measures when during work dust can
disconnect the plug
develop that is harmful to one's health, combustible or ex-
● Never use tool when cord is damaged; have it
plosive (some dusts are considered carcinogenic); wear a
replaced by a qualified person
dust mask and work with dust/chip extraction when con-
● Always check that the supply voltage is the same
nectable
as the voltage indicated on the nameplate of the
6