Werbung
eine feuerfesten Unterlage gelegt werden und hier die Brennstofftabletten restlos abge-
brannt werden.
16. Das Dampfabsperrventil bei sichtbarer Dampfentwicklung (Manometerstand ca. 1
bar) durch eine Drehung nach links öffnen. Das Schwungrad von Hand anwerfen, damit
das in der Dampfleitung und dem Zylinder befindliche Kondenswasser entweichen kann.
Dadurch setzt sich die Dampfmaschine in Betrieb. Die Drehzahl des Schwungrades kann
durch das Dampfabsperrventil geregelt werden.
17. Der Kondenswasserbehälter muss während des Dampfbetriebes mehrfach entleert
werden. Hierzu vorher das Dampfabsperrventil schließen und die Dampfmaschine stop-
pen.
18. Nach Beendigung des Dampfbetriebes und dem Abkühlen sollte die Dampfmaschine
gewartet werden. Noch im Kessel vorhandenes Wasser durch das Öffnen des Wasserab-
lassventils entleeren. Hierzu das Wasserablassventil öffnen und die Dampfpfeife durch
leichtes Ziehen an der Kette öffnen - so entsteht kein Unterdruck beim Entleeren des Rest-
wassers. Vorsicht bei heißem Wasser! Im Kessel verbleibendes Wasser kann der Funk-
tion nicht schaden, aber evtl. zu Ablagerungen an dem Schauglas führen. Kalkrückstände
am Wasserstandsschauglas oder im Kessel auf keinen Fall mit Essig oder sonstigen
stark ätzenden Mitteln entfernen
(Empfehlung: Verwendung eines kalklösenden Mittels, welches Messing und Lötzinn
nicht angreift). Eine Rußbildung an der Unterseite des Kessels beeinflusst ebenfalls nicht
die Funktion und kann mit einer Bürste entfernt werden. Zum Abschluss das Modell tro-
ckenputzen.
Garantie:
Alle WILESCO-Dampfmodelle durchlaufen eine Endkontrolle. Bei einem evt. Fehler
können Sie die Dampfmaschine über Ihren Fachhändler oder direkt an uns einsenden.
Wir bitten um Verständnis, dass bereits angeheizte/gebrauchte Modelle nicht ge-
gen neue ausgetauscht werden können. Die häufigsten Reklamationen sind undichte
Dampfkessel. Die Lötnaht wird durch Beheizung ohne ausreichenden Wasserstand zer-
stört. In solchen Fällen verflüssigt sich das Lötzinn an der Lötnaht tropfenförmig und der
Kessel wird undicht. Dies ist ein eindeutiger Beweis, dass der Kessel trockenbeheizt wur-
de. Bitte beobachten Sie stets sorgfältig den Wasserstand, da eine Trockenbehei-
zung jegliche Garantieansprüche ausschließt.
Umweltschutz wird auch bei uns groß geschrieben. Somit haben Sie die Möglichkeit
nach einem langen Dampfmaschinenleben diese und auch die Original-Verpackung an
uns zurückzugeben. (Versandkosten werden nicht übernommen.) Alle zurückgesandten
Modelle / Verpackungen werden von uns einem fachgerechten Recycling zugeführt.
Dieses Modell ist ausschließlich für die oben beschriebene Funktion bestimmt.
Technische Änderungen behalten wir uns vor.
WILESCO wünscht Ihnen nun viel Spaß mit Ihrer Dampfmaschine und „Volldampf vo-
raus„!
Attention! Before operating this steam engine model
please read and observe thoroughly the operation
instructions.
precautions for your own safety:
1. For safety reasons, children should run the Steam
Engine only under supervision of adults (recommended
age: from 8 years on, not suitable for children under 36
months). While the Engine is running and until its complete cooling, the Steam Engine
must be under constant observation.
2. Each irregularity in the course of the running of the Steam Engine can be repaired by a
competent and authorized person or by WILESCO themselves. Otherwise any warranty
expires.
3. Any unauthorized alteration, repair or manipulation to the standard specification will
also invalidate the warranty.
4. The parts which are under steam pressure as boiler, spring loaded safety valve etc.
leave our premises only after a 100% control. The spring loaded safety valve must not be
manipulated. The running of the Steam Engine without any spring loaded safety
valve is not allowed The spring loaded valve must be checked before each running with
a pression on the spring or a small pull on the upper valve rod. If lime deposits by hard
water are on the spring loaded safety valve, the valve must be changed immediately.
5. High temperatures: Due to the principles on which your Steam Engine operates, the
boiler house, the spring loaded safety valve, the steam pipes etc. become very hot. Do not
touch in order to avoid the risk of burns.
6. Safety precautions: During operation, take care that children do not touch any of the
moving parts.
7. Danger if the boiler is heated without enough water! Always ensure
that there is enough water in the boiler of the Steam Engine. Caution:
Water has to be refilled when adding new WiTabs dry fuel tablets. The
water must always be visible at least at the lower end of the sight
glass, otherwise the joints become leaking and the boiler will be destroyed.
Any following claim, damage or consequential damage cannot be accepted.
If a leak occurs in the boiler or any other part where water or steam escape, stop the
Steam Engine immediately (remove the burner tray and operate the steam whistle). Any
necessary repair should be carried out by authorized staff or at the WILESCO company.
8. The Steam Engine meets all safety standards and actual regulations. Each boiler has
been submitted to a bursting pressure and water test of 5 bar. The operating pressure is
max. 1,5 bar.
9. Keep the operating instructions with your Steam Engine.
10. We advise you to place the stationary Steam Engine on a non sliding surface or fix it
onto a coated chipboard (approx. 16 mm thick) with 4 woodscrews (3,4 x 45 mm). The
size of the board depends on how many models will be run with the Steam Engine.
Caution: Don't operate the steam model near flammable objects or on
temperature-sensitive surfaces.
Operating instructions
Important
information
and
11. Unscrew the spring loaded safety valve and fill the boiler with the funnel approx. 3/4
full (upper edge of the water gauge glass), if possible with warm water. Lift the funnel
slightly so that the air inside the boiler can escape. Use only deficient in lime water or,
even better, water without any lime (e.g. distilled water). Then refit the spring-loaded
safety valve.
12. Screw the pressure gauge with sealing ring(s) onto the boiler. Bring its face to the
front side (eventually use further sealing rings of different thicknesses).
13. Screw the steam whistle onto the boiler. Imperatively use the spanner provided with
the Engine. Do not tighten by turning the lever as this will be damaged. When screwing
in the steam whistle, the lever with the chain should point outwards (use washers if
necessary) so that the chain which operates the whistle does not come in contact with the
boiler. Pull the chain gently to operate the whistle. Note: The steam whistle can be
used to check any overpressure in the boiler. Assemble the smoke stack with the
enclosed screws on the back side of the boiler house.
14. Before you oil the cylinder, turn off the steam supply valve. Then turn off the oil
filler screw and fill in
with WILESCO Steam Oil (item n° Z 83) while turnin g the flywheel several times so
that the oil is grawn in. Oil again when you refill dry spirit tablets so that the piston does
not seize (2-3 drops of oil are sufficient for an operating time of abt. 10 minutes). Keep
the cutout valve closed during the oiling procedure. Oil a bit all bearings and
linkages. Before refilling the boiler with water, check by operating the steam whistle that
there is no pressure is in the boiler.
15. Place 3 WiTabs dry fuel tablets upright in the burner slide (no more
than 3 pcs.) and light them. Use only the original WILESCO burner slide.
Caution: because of the risk of danger from an open flame, always
take the necessary safety precautions. The burner slide is adjustable.
The oxygen supply and the flame height can be adjusted by moving the
burner slide in relation to the air holes of the burner slide guide in the
boiler house. Before adding new fuel tablets, always check the water level
and refill the boiler with water to ensure that the boiler does not run dry. The ratio of fuel
tablets to the quantity of water in the boiler is designed so that the boiler cannot run dry
without any added fuel tablets. The burner slide must be completely pushed in.
Important: After the heating process, remove the burner slide from the guide
whilst it is still hot, otherwise unburnt fuel may cause the slide to stick. If the slide
becomes stuck, it can be removed by tilting it slightly to the left or right.
Caution: In order to burn properly, WiTabs dry fuel tablets require a lot of
oxygen That is the reason why during indoor use the room should be
well ventilated. To prevent unpleasant smells, the fuel tablets should burn
out - they should not be blown out. If there is not enough water in the
boiler, place the burner slide on a fireproof plate until the tablets have
completely burnt out .
16. When steam appears (manometer indicating approx. 1 bar), turn once
the steam supply valve to the left to open it. Then turn the flywheel by hand to let the
condensation in the pipes and the cylinder escape. Then the steam engine will start to
operate. The speed of the flywheel can be adjusted through the steam regulator.
17. The condensed water tray must be emptied several times while the Steam Engine is
running. Before you empty the condensed water tray, turn off the steam regulator and
stop the Steam Engine.
18. After the operating of the Steam Engine and its cooling, the Engine should be
serviced. Pour out any water left in the boiler by opening the water drain valve. For this,
unscrew the spring loaded valve, then open the steam whistle by pulling gently on the
chain. This will prevent a vacuum when the residual water is drained off. Be very
careful if the water is still hot! Any water left in the boiler cannot do any damage, but
might leave deposits on the sight glass. Any lime formation on the sight glass or in the
boiler have not to be removed in any case using vinegar or corrosive agent (advice:
use a lime dissolving agent which does not attack the brass and the solder). The building
of soot on the lower side of the boiler does not influence the function and can be removed
with a brush. Finally, dry the model with a clean cloth.
Warranty:
19. All WILESCO Steam Engines are carefully checked before leaving the factory.
However, if a problem arises, you can return the Steam Engine to a specialized
distributor or directly to WILESCO. We are sure you will understand that models
which had already been fired or used cannot be replaced by new ones. The most
safety
frequent claims are leaking boilers. The solder will be destroyed if there is not enough
water in the boiler. In this case the solder liquefies drop-shaped and the boiler becomes
leaking. This is an obvious proof that the boiler was fired without enough water. Please
watch always carefully the water level, because the heating without enough water
excludes any warranty claim.
This Steam Engine is exclusively meant for the above described function.
Subject to technical change without prior notice.
WILESCO wishes you a good time with your Steam Engine and „full steam ahead"!
Attention ! Avant la mise en marche de ce modèle d'une
machine à vapeur veuillez lire et respecter ce mode d'emploi
soigneusement. Remarques importantes et mesures à observer
pour votre sécurité.
1. Pour des raisons de sécurité, les enfants doivent utiliser la
machine à vapeur uniquement sous la surveillance d'un adulte
(âge conseillé : à partir de 8 ans, non pas recommandé pour enfants en dessous de
36 mois). Au cours de son fonctionnement et jusqu'à son refroidissement complet, la
machine doit être constamment sous surveillance.
2. Tout défaut de fonctionnement de la machine à vapeur doit être réparé par un
détaillant agréé ou par la société WILESCO elle-même. Dans le cas contraire, aucune
garantie ne pourra être prise en considération.
3. Toute modification, réparation ou manipulation de la machine à vapeur non prévue
dans le mode d'emploi annule la responsabilité.
4. Toutes les pièces soumises à la pression comme la chaudière, la soupape de sécurité à
ressort, etc. sont vérifiées à 100 % avant de quitter notre usine. Ne dérégler en aucun cas
2
Werbung
