Werbung
Verfügbare Sprachen
Verfügbare Sprachen
- Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent kickback
and loss of control over the power tool.
Safety warnings specific for Grinding and Abrasive Cut-
ting-Off operations
- Use only wheel types that are recommended for your
power tool and the specific guard designed for the se-
lected wheel. Wheels for which the power tool was not de-
signed cannot be adequately guarded and are unsafe.
- The guard must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator. The
guard helps to protect operator from broken wheel frag-
ments, accidental contact with wheel and sparks that could
ignite clothing.
- Wheels must be used only for recommended applica-
tions. For example: do not grind with the side of the
cut-off wheel. Abrasive cut-off wheels are intended for pe-
ripheral grinding; side forces applied to these wheels may
cause them to shatter.
- Always use undamaged wheel flanges that are of cor-
rect size and shape for your selected wheel. Proper
wheel flanges support the wheel thus reducing the possi-
bility of wheel breakage. Flanges for cut-off wheels may be
different from grinding wheel flanges.
- Do not use worn down wheels from larger power tools.
Wheels intended for larger power tools are not suitable for
the higher speed of a smaller tool and may burst.
Additional safety warnings specific for abrasive cutting
off operations
- Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth of
cut. Overstressing the wheel increases the loading and sus-
ceptibility to twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
- Do not position your body in line with and behind the
rotating wheel. When the wheel, at the point of operation,
is moving away from your body, the possible kickback may
propel the spinning wheel and the power tool directly at you.
- When wheel is binding or when interrupting a cut for
any reason, switch off the power tool and hold the pow-
er tool motionless until the wheel comes to a complete
stop. Never attempt to remove the cut-off wheel from
the cut while the wheel is in motion otherwise kickback
may occur. Investigate and take corrective action to elimi-
nate the cause of wheel binding.
- Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter the
cut. The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
- Support panels or any oversized workpiece to mini-
6
mize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut and
near the edge of the workpiece on both sides of the wheel.
- Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
Safety warnings specific for sanding operations
- Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when select-
ing sanding paper. Larger sanding paper extending be-
yond the sanding pad presents a laceration hazard and may
cause snagging, tearing of the disc, or kickback.
Safety warnings specific for wire brushing operations
- Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
- If the use of a guard is recommended for wire brush-
ing, do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
Product description and Specifications
Description
A
Start-up switch
B
Auxiliary handle
C
Disc protector
D.
Ventilation openings
E
Spindle blocking button
F
Spindle
H
Support plate
I
Disc (not included)
J
Clamping nut
K
Tightening key
L
Collard of guard
M
Bolt
N
Lever
Instructions for use
Before use:
- Make sure that all the product's packaging has been re-
moved.
- Ensure that the selected tension on the voltage selector coin-
cides with the tension of the mains.
- Before connecting the power cord to the mains power supply
ensure the switch is in the off position.
- Ensu
- Prep
use:
Fitting
Fitting
- N
place.
- T
guard
- Unpl
- Fit th
- If the
- Turn
- To fa
Fitting
- Unpl
Use o
greate
iliary h
depen
Fitting
- Unpl
- Block
(E). Th
blockin
- With
the sp
- Asse
- Asse
The p
ness o
- Once
ton (E
Use:
- Conn
- Turn
- Be c
the sp
materi
- Whe
angle
30º fo
- Whe
move
at the
of mat
the ad
would
in an u
Werbung
