Herunterladen Inhalt Inhalt Diese Seite drucken

Simplified Eu Declaration Of Conformity - Jungheinrich WMT11X Inbetriebnahmeanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 5
Quick Installation Guide || Jungheinrich WMT11X Terminal
Jungheinrich WMT11X Quick
Installation Guide
1. Correct Use
The terminal must be operated and stored under the following
conditions:
Temperature during operation
Temperature during storage
Air humidity in operation and storage 10% to 95% without
condensate.
The terminal is protected against dust and jets of water in
accordance with protection rating IP65.
Use in areas where there is a risk of explosion is prohibited.
2. Installation of the Grab Handle
WARNING!
Installation work on the terminal may be performed only by
suitably trained electricians when the terminal has been
secured and disconnected from the power.
Install the grab handle (Figure II, item 5) on the terminal using
the screws supplied in the following sequence from the inside
outwards:
1.
WMT110 terminal
2.
Mounting bracket
3.
Washer
4.
Torx Tx30
1.
WMT115 terminal
2.
Nord-Lock washer (large)
3.
Mounting bracket
4.
Nord-Lock washer (small)
5.
Torx TX50
6.
Cap
2.2 Installation of a VESA Support
Alternatively, the terminal can be installed using the VESA 75
hole pattern (Fig. II, item 3) with a suitable support, e.g. RAM
Mount.
Note
The relevant safety measures must be observed at all
times when handling electrostatically hazardous
components. (DIN EN61340-5-1 / DIN EN 61340-5-2).
3.1 Open the Service Chamber Cover
Remove the screws from the service chamber cover (Fig. II,
item 4) using a Torx Tx10 screwdriver. Remove the service
chamber cover from the terminal.
3.2 Connection of the Cables
Connect all required cables within the service chamber. Use
the grommets (Fig. III, item 8) to ensure the IP65 protection
rating. The grommets have a slot on the side for inserting the
cables.
3.3 Connection of the Power Source
The terminal is supplied via a 3-pin connector (Phoenix
Contact MC 1.5/ 3-STF-3.81) with either 12 V or 24 V/48 V DC
depending on the version (Fig. III, item 7).
© Jungheinrich AG, Friedrich-Ebert-Damm 129, 22047 Hamburg
EN
-30°C to +50°C
-40°C to +80°C
1: 0 V DC
2: Release contact/ignition
3: 12 V or 24 V/48 V DC
Note
Check the required power supply on the terminal data plate
(Fig. II, item 2).
– operating voltage 6.5 V to 16 V DC
Input: 12 V
Input: 24/48 V – operating voltage 16.8 V to 72 V DC
Earthing to the truck chassis is via 2x1.5 mm² flat-plug
contacts (Fig. III, item 6).
Caution!
The protective conductor must always be attached.
Without the protective conductor, there is a risk of
overvoltage at the terminal.
The power supply must be equipped with a fuse:
7 A for 12 V DC
4 A for 24 V/48 V DC
3.4 Close the Service Chamber Cover
Once the work is complete, the removed service chamber
cover needs to be re-installed on the terminal with the screws.
Make sure that the grommets (Fig. III, item 8) are in the
correct position during installation.
4. Switching on the Terminal
Once the terminal has been connected to the power source
and the service chamber has been re-sealed, the terminal can
be commissioned.
To do this, press the Power-On button on the front for approx.
1 second (Fig. I, item 1).
Note
To avoid condensation water, the terminal must not be
switched on until it has adjusted to the room temperature.
If the terminal shows obvious signs of damage, caused e.g. by
incorrect operating/storage conditions or improper use, it must
be taken out of commission immediately and secured against
inadvertent recommissioning.
5. Opening the Terminal
The terminal (apart from the service chamber) must not be
opened by personnel not authorised by Jungheinrich; action to
the contrary will invalidate the warranty.
6. Support
You can find more information about configuring and
operating the terminal at:
https://support-rdt.jungheinrich.com/

7. SIMPLIFIED EU DECLARATION OF CONFORMITY

Jungheinrich Aktiengesellschaft hereby declares that the
aforementioned radio equipment satisfies Directive
2014/53/EU.
The full text of the EU Declaration of Conformity is available at
the following address:
www.jungheinrich.com/declaration-of-conformity
v1.2

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis