Declaration Of Conformity; Battery Charging - Berner BACCS 10,8 V LI Originalbetriebsanleitung

OBJ_BUCH-2433-001.book Page 19 Friday, March 6, 2015 12:37 PM
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with all relevant provisions of the direc-
tives 2009/125/EC (Regulation 1194/2012),
2011/65/EU, until 19 April 2016: 2004/108/EC,
from 20 April 2016 on: 2014/30/EU, 2006/42/EC
including their amendments and complies with the
following standards: EN 60745-1, EN 60745-2-5.
Technical file (2006/42/EC) at:
Berner Trading Holding GmbH,
Bernerstraße 6,
74653 Künzelsau, GERMANY
Armin Hess
Chairman of the Management Board
06.02.2015, Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau, GERMANY
Assembly

Battery Charging

 Use only the battery chargers listed on the ac-
cessories page. Only these battery chargers are
matched to the lithium-ion battery of your power
tool.
Note: The battery supplied is partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before us-
ing your power tool for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging by the "Electronic Cell Protection
(ECP)". When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted tool no longer rotates.
 Do not continue to press the On/Off switch af-
ter the machine has been automatically
switched off. The battery can be damaged.
Observe the notes for disposal.
1 619 P12 705 • 6.3.15
Removing the battery
The battery 1 is equipped with two locking levels
that should prevent the battery from falling out
when pushing the battery unlocking button 2 unin-
tentionally. As long as the battery is inserted in the
power tool, it is held in position by means of a
spring.
To remove the battery 1, press the battery unlock-
ing button 2 and pull the battery out of the power
tool toward the rear. Do not exert any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control
indicator 15 indicate the charge condition of the
battery 1. For safety reasons, it is only possible to
check the status of the charge condition when the
machine is at a standstill.
Press the On/Off switch 4 halfway or completely
through to indicate the charge condition.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pressing the On/Off
switch 4, the battery is defective and must be re-
placed.
Mounting/Replacing the Saw Blade
 Before any work on the power tool, remove the
battery.
 When mounting the saw blade, wear protec-
tive gloves. Danger of injury when touching the
saw blade.
 Only use saw blades that correspond with the
characteristic data given in the operating in-
structions.
 Do not under any circumstances use grinding
discs as the cutting tool.
Removal of the Saw Blade (see figure A)
For changing the cutting tool, it is best to place the
machine on the face side of the motor housing.
– Press the spindle lock button 6 and keep it
pressed.
 The spindle lock button 6 may be actuated on-
ly when the saw spindle is at a standstill. Oth-
erwise, the power tool can be damaged.
– With the Hex key 5, unscrew the clamping bolt
25 turning in rotation direction .
– Tilt back the retracting blade guard 21 and hold
firmly.
– Remove the clamping flange 24 and the saw
blade 23 from the saw spindle 20.
Capacity
2/3
1/3
<1/3
Reserve
English | 19