V2 WALLY Handbuch Seite 4

The new superheterodyne receiver always guarantees a correct
functioning in disturbed environments: its good sensitivity and
high selectivity make it immune from most disturbances around
the frequency reception area. The new self-learning
programming system enables the memorization of the
PERSONAL PASS series transmitters.
• It is possible to store up to 240 different codes with
self-learning mode.
• It is also available in the 4-channel version PLUS, which can
store up to 1008 different codes (WALLY4PLUS,
WALLY4/434P, WALLY4/868P)
• Three different functions can be programmed by means of
SW1 key for the outputs: monostable, bistable and timer.
• Self-learning of transmitters managed by radio.
• Management of the substitutive transmitter.
• It is possible to enable or disable the ROLLING CODE mode.
• Memory full warning: the receiver blinks 15 times.
• It can be connected to the PROG2 portable programmer
(version 3.6 or newer), which allows to manage devices by
means of WINPPCL (version 2.1 or newer)
CAUTION: before inserting the receiver into the relevant
TX connector of the PROG2, make sure that it is not
powered.
PROGRAMMING
The self-learning programming system enables the code
memorization and the setting of the following functioning
modes:
MONOSTABLE: it activates the corresponding relay through the
time of tx transmission. When the transmission stops, the relay
goes automatically off.
BISTABLE: it activates the corresponding relay on the first tx
transmission. The relay goes off on the second transmission.
TIMER: the tx transmission activates the corresponding relay
which goes off after the set time (max 7,5 minutes).
PROGRAMMING OF THE MONOSTABLE
FUNCTION
Select the desired channel in accordance with the following
table:
SELECTED CHANNEL
CHANNEL 1 MONOSTABLE
CHANNEL 2 MONOSTABLE
CHANNEL 3 MONOSTABLE
CHANNEL 4 MONOSTABLE
• Press the SW1 key of the receiver N times, as indicated
above: the relevant led goes on
• Within 5 seconds, press and hold pressed the push button of
the transmitter
• The led of the receiver goes out and goes on again: the code
was stored and the receiver keeps waiting for 5 secs for a
new code to memorize
LED ON
N°IMPULSES SW1
L1 L2 L3 L4
•
1
2 •
3
4
PROGRAMMING OF THE TIMER FUNCTION
To memorize the TIMER function on the first channel, proceed as
follows:
1. Press and keep pressed the SW1 button of the receiver :
the led L1 (relating to the first channel) lights up for a few
seconds.
2. When led L1 goes off, release the SW1 button. Led L1 starts
a sequence of flashings at low speed (1 flash per second).
The number of flashing corresponds to the time which can
be set as shown in the table.
3. Count the number of led L1 flashings corresponding to the
time you wish to set. Press the rx button SW1 during the
wished flashing: the sequence of flashings stops and led L1
remains on.
4. Within 5 seconds, press and hold pressed the push button of
the transmitter.
5. The led of the receiver goes out and goes on again: the code
was stored and the receiver keeps waiting for 5 secs for a
new code to memorize.
To programme channels no. 2, 3 and 4, repeat the above
mentioned steps no. 2, 3 and 4, taking into consideration
leds L2, L3 or L4 in accordance with the selected channel.
N° Flashing
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PROGRAMMING OF THE BISTABLE
FUNCTION
To memorize the bistable function on the first channel, proceed
as follows:
•
•
1. Press and keep pressed the receiver SW1 button : led L1
(relating to the first channel) lights up for a few seconds.
2. When led L1 goes off, release SW1 button; led L1 starts
flashing at low speed (1 flash per second). When the 30
flashings of the timer function are over, led L1 remains on.
3. Within 5 seconds, press and hold pressed the push button of
the transmitter.
4. The led of the receiver goes out and goes on again: the code
was stored and the receiver keeps waiting for 5 secs for a
new code to memorize.
To programme channels no. 2, 3 and 4, repeat the above
mentioned steps no. 2, 3 and 4, taking into consideration
leds L2, L3 or L4 in accordance with the selected channel.
Time N° Flashing
01 sec. 17
02 sec. 18
03 sec. 19
04 sec. 20
05 sec. 21
06 sec. 22
07 sec. 23
08 sec. 24
09 sec. 25
10 sec. 26
11 sec. 27
12 sec. 28
13 sec. 29
14 sec. 30
15 sec. 31
30 sec.
Time
1 min.
1,5 min.
2 min.
2,5 min.
3 min.
3,5 min.
4 min.
4,5 min.
5 min.
5,5 min.
6 min.
6,5 min.
7 min.
7,5 min.
BISTABLE