Werbung
Verfügbare Sprachen
Verfügbare Sprachen
English
TR Series Traveler Operation Guide
Assembly of the Rain Bird TR Series Traveler
Thank you for your purchase of the Rain Bird TR. Please follow the instructions below for assembly.
Tools required:
• Large regular flat-headed screwdriver.
• Rubber mallet
1
• 13mm /
⁄
" wrench
2
• Teflon tape
Parts Included:
Model
4-wheel 3-wheel
Rear Axles (A)
2
2
Stake (B)
1
1
TR Body Assembly (C)
1
1
Wheel Caps (D)
4
2
Wheels (E)
4
2
Front Axles (F)
2
-
Front Axle Wheel Bolts (G)
2
-
Front Axle Wheel Washers (H)
2
-
Caster (I)
-
1
Caster Bolt, Nut and Washer (J) -
1
Assembling the TR
1. Remove the TR's plastic cover.
2. Insert the rear axles (A) into the frame of
the TR (C). Secure with the set screws
(pre-installed in Body Assembly) using a
regular flat-head screwdriver.
3. For four-wheeled models, attach the front
axles (F) to the TR body using the enclosed
bolts and washers (G & H). For three-
wheeled models, attach the caster (I) with
the bolt, nut and washer (J) enclosed.
4. Place the wheels (E) on the axles and
secure with wheel caps (D).
5. Wrap the sprinkler threads with Teflon
tape and install sprinkler head.
6. Replace the plastic cover.
C
A
4-wheel model pictured
B
F
E
J
Operation Speed
Pressure Operation
Pressure Operation
reading
Speed
reading
speed
(bars)
(m/hr)
(PSI)
(ft/hr)
2.5
9.0
36
29.5
3.0
11.0
43
36.1
3.5
13.5
51
44.3
4.0
15.0
58
49.2
4.5
17.0
65
55.7
5.0
19.0
72
62.3
5.5
20.5
80
67.2
6.0
22.0
87
72.1
Optimal performance achieved after a 30-hour
break-in period.
Operation of the Rain Bird
TR Series Traveler
Section 1 – Operating the TR
1. Place the TR in the starting location.
2. Lay out the hose according to F1 or F2,
depending on location. Connect hose to TR.
3. Remove the cover of the TR.
4. Disconnect the security spring (K) from the
crank (L).
5. Unwind steel cable along the intended travel path.
Attach to the TR stake (B) at the end of the
G
travel path.
H
6. Tighten any slack in the cable with the crank..
7. Reconnect the security spring to the crank.
8. Push the shut-off valve lever (M) forward and lock
into position with latching arm (N).
D
9. Open the turbine control valve (O) completely by
turning counterclockwise.
10. Start the water flow.
I
11. Check pressure gauge (P) reading for true
operating pressure at the driving nozzle. Speed
is controlled by adjusting turbine control valve
according to the Operation Speed chart on the
previous page.
12. Replace the TR's cover. The TR operates in a direct
path toward the stake and will shut off automatically
at the end the path.
Section 2 – Maintenance
•
The turbine and transmission of the TR are
maintenance free.
•
The roller and wheel axles should be greased once
a year.
For travelers in freezing climates, ensure that the turbine
feeder line (Q) is emptied at the end of the season to
avoid cracking of internal components due to freezing.
This can be done by partially opening valve (O) and
lifting the rear of the unit, allowing the water to drain.
F1
Cable
Anchor
Drag Hose
Cable
Anchor
F2
Cable
Anchor
Drag Hose
Drag Hose
Cable
Anchor
N
L
K
M
O
Q
P
The warranty on the Rain Bird TR shall be
for 3 years from the manufacturing date
code on the TR unit.
Werbung
