Operation; Reverse Function - Rexel Mercury RSS1627 Bedienungsanleitung

Shredder Control Panel
On/Off Forward
m
Safety First
This means you should be careful because long hair can become
entangled in the cutting head. This could hurt you.
This means don't reach into the feed opening of the cutting head.
This could hurt you.
This means be careful of ties and other loose clothing which could
become entangled in the cutting head. This could hurt you.
This means keep children away from shredder.
This means do not use aerosol sprays anywhere near the unit.

Operation

Connect shredder to mains supply
1
2 Press the central power on button (b). This will switch the power on.
The shredder will now be in standby mode but will not operate until
the button with the green triangle is pressed. While the shredder is in
standby mode, the anti-jam indicator will flash green.
3 To commence shredding, press the right hand auto feed button (c)
which stops the flashing on the anti-jam indicator. The indicator will now
glow green.
This sets the shredder into auto mode and initiates the Mercury anti jam
mechanism. You are now able to shred.
Insert paper to be shredded into the feed area. The Mercury anti jam
4
mechanism will sense the thickness of the paper being shredded.
If the paper thickness is within the shredders capacity the motor will
start and your documents will be shredded. Cutters will stop once the
shredding process is complete.
If the paper thickness is greater than the shredders sheet capacity the
anti-jam indicator will turn from green to red and the motor will not run.
If this happens, remove some of the sheets from the paper stack and
5
re-try until the anti-jam indicator reverts back to green, the shredder will
then automatically start and allow the paper to be shredded.
If the shredder is left in auto mode for more than 10 minutes without
being used, the shredder will automatically switch off in order to save
power.

Reverse Function

Should you wish to reverse the shredding direction whilst shredding a
1
document, a reverse button (d) has been fitted for your convenience.
By pressing the reverse button the shredding cutters will change
2
direction allowing the retrieval of the document being shredded. The
anti-jam indicator will turn to red.
The reverse function will only run whilst the button is being pressed.
3
When the reverse button has been released the shredder will revert to
stand by mode.
4 To turn back to auto mode simply press the right hand auto feed button
again (button with the green triangle).
CD Shredding
The Mercury models can also shred CD's.
Reverse
Pull down the orange CD guide (f) located in the centre of the feed area
1
and extend the sides to fill the feed area.
Switch the shredder to auto mode and place CD into the centre of the
2
CD Slot, this will activate the shredder as before.
Only 1 CD can be shred at a time.
Credit Cards
Switch shredder to auto mode and place credit card into the centre of the
shredder. It is important to place in the centre of the shredder as this is
where the auto run sensors are located.
Rare Occasions of Jamming
In the unlikely event of the shredder jamming, use the reverse function to
unblock the shredder. (see Reverse function section)
Alternating between the reverse function and the forward run will help
unblock the feed area. To trigger the permanent forward run mechanism,
press Auto/On button (green triangle) down for 2 seconds.
Once the jam is clear, press the right hand auto button once to revert back
to auto mode. You can now resume shredding as normal.
Bin Full
When the bin is full the shredder will not function and the bin full symbol will
illuminate red.
When this happens you must empty the bin.
• Pull out the bin to empty
If the bin is not relocated correctly, the anti-jam indicator will continue to
flash red. Once relocated correctly the anti-jam indicator will return to green.
Shredder Waste Sacks
Please refer to illustrations to see how to insert and remove paper bag.
Insert recyclable paper bag (2102063 [20 pack]) into the shredder bin and
hook in place using the holes punched in the bag and locating points on the
front internal bin face and rear lip. Once full with paper, unfold the doubled
over bag flaps to make the full bag easy to remove from the bin. Tuck over
the rear flap before folding over the front sealing flap and sealing the bag
closed using the adhesive strip. Most local authorities now accept paper for
recycling please contact your local authority for more information.
Over Heating
If the shredder is used continuously for long periods of time the shredder
may overheat. If this occurs the thermometer symbol on the indicator panel
will flash blue.
When the shredder is ready to be used again the thermometer will stop
flashing and the anti-jam indicator will flash green once again. To resume
shredding press the auto button (green triangle).
G
5