Atlas NFS 166 Bedienungsanleitung Seite 10

Preparations for use
Standing time
After the freezer is properly installed and well cleaned, do not
switch it on immediately. Make sure to energize the freezer after
more than 1 hour's standing, so as to ensure its normal opera-
tion.
Cleaning
Confirm the accessory parts inside the freezer and wipe the in-
side with a soft cloth.
Power-on
Insert the plug into the solid socket to start the compressor. Af-
ter 1 hour, open the freezer door, if the temperature inside the
freezer compartment drops obviously, it indicates the refrigera-
tion system is working normally.
Storage of food
After the freezer runs for a period of time, the internal tempera-
ture of the freezer will be automatically controlled according to
the user's temperature setting. After the freezer is fully cooled,
put in foods, which usually need 2-3 hours to be fully cooled. In
summer, when the temperature is high, it takes more than 4
hours for the foods to be fully cooled (Try to open the freezer
door as less as possible before the internal temperature cools
down).
If the freezer is installed in the moisture place, make sure to
check whether the ground wire and leakage circuit breaker are
normal. If vibration noises are produced due to the freezer con-
tacting the wall or if the wall gets blackened by air convection
around the compressor, move the freezer away from the wall.
Setting up the freezer may cause jamming noise or image chaos
to the mobile phone, fixed-line telephone, radio receiver, televi-
sion surrounding it, so try to keep the freezer as far away as pos-
sible in such case.
Functions
When the freezer system is connected to power supply for the
first time, all icons on the display panel gets illuminated for 2s,
and the system runs at -18°C by default.
Temperature setting
Temperature can be adjusted by pressing the "SET" key. Every
time when the "SET" key is pressed, the current mode indicator
lights off while the next mode indicator lights up, with the said
mode setting validated if no key operation within 5s (or else, the
mode setting will be invalid). After the setting takes effect, tem-
perature will be immediately controlled as per the mode setting.
The temperature modes cycle as following:"-16°C-> -18°C-> -
20°C-> -22°C-> -24°C-> (°C
Fast freezing
When the fast freezing function is enabled, the compartment
temperature can be cooled down in a rapid manner, which is
beneficial to the prevention of food nutrition against lost and the
preservation of freshness.
After a cumulative running period of 26 hours, the fast freezing
function will exit automatically, with the temperature mode re-
stored to that set before the fast freezing function is enabled.
Door open alarm
When the freezer door keeps open for more than 3 minutes, the
buzzer starts issuing alarms, which can be suspended for 3
fast freezing) -> -16°C ."
minutes by pressing any key, but they will not be stopped until
the said door gets closed.
Power-cut memory
In case of power failure, the freezer will maintain the operating
state before power failure when power supply is restored.
Power-on delay
In order to protect the freezer compressor from being damaged
in the case of short-time power failure (i.e., less than 5 minutes),
the compressor will not be started immediately after it is pow-
ered on.
Defrosting
The freezer can defrost automatically or manually.
When the freezer is not defrosting, the automatic defrosting
program can be enabled by holding down the SET key for 15s,
with all the mode indicator lights illuminated, refrigeration
stopped, and defrost heating started. During the defrosting pro-
cess, you can hold down the SET key for 3s to stop defrosting
manually, or wait until the defrosting program gets exited auto-
matically.
In order to avoid frequent defrosting actions of the freezer, do
not access to the defrost function during the defrosting process;
and make sure not to enable the defrost function again within 10
minutes after it is manually disabled.
Fault alarm
When the alarm indicator keeps flashing (with the corresponding
indicator light of "-16, -20, -24, or fast freezing" flickering simul-
taneously), it indicates fault with the freezer. Please contact the
aftersales person for visiting service in such case.
Instructions for food storage
Food storage locations
Shelf: When taking the shelf out, lift it upwards, and then pull it
out; when installing the shelf, make sure to place it into position
before putting it down.
Crisper box (drawer): You can pull out the drawer for access to
foods.
Do not put too many or too weight foods inside the freezer. Keep
enough space between foods; if too close, the cold air flow will
be blocked, thus affecting the refrigeration effect. Do not store
excessive or overweight foods, to avoid the shelf from being
crushed. When storing the foods, keep a distance away from the
inner wall; and do not place the water-rich foods too close to the
freezer rear wall, lest they get frozen on the inner wall.
Freezer mode：
Long-term storage of foods: The freezer compartment, where
the temperature is generally controlled below -18°C, is suitable
for the preservation of foods for a long term, but the shelf life
indicated on the food packages should be abided by.
Freezer drawer: Used for the frozen food storage; For the mass
pieces of meat or fish, cut them into smaller ones, pack them up
separately with the fresh-keeping bags, and distribute them
evenly in the drawer.
Fast freezing
1 Refer to the description about fast freezing function in the
"Function" section.
2 Compared with the normal freezing, fast freezing enables
food to pass through the maximum ice crystal formation zo-
ne at the fastest speed. Fast freezing can freeze the food wa-
ter content into fine ice crystals, without damaging the cell
membrane, so cell juice will not be lost when thawing, and
the original freshness and nutrition of food can be maintai-
ned.
9