Bebecar Ip-Op Classic Bedienungsanleitung Seite 36

GB
READ THESE INSTRUCTIONS CAREFULLY BEFORE
USE AND KEEP THEM FOR FUTURE REFERENCE
YOUR CHILD'S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS
WARNING: This pushchair has been designed to be operated as shown in the instructions supplied.
Not to do so may cause damage and render your guarantee void.
1 - TO UNFOLD: When opening the pushchair with the adjustable handle, ensure that the handle is in line with the main
handle.
2 - Pull gently on handle of pushchair, and press down on metal tube of pushchair with your foot as indicated by the
figure, until primary locks engage with a click. The secondary lock will automatically engage.
NB: Check security of the pushchair by pulling on handle and pushing right and left moulding as shown.
3 - STEERING - NON-STEERING: The front wheels can be used in either mode.
Slide lever (on both sides of chassis) to the upwards position for steering, as indicated in the figure.
For non-steering wheels press button and lever will slide in a downward position.
NB: When using your pushchair on rough ground we recommend non-steering mode.
4 - BRAKE OPERATION: To apply brake, press down on pedal.
5 - To release brake, pull up the pedal.
6 - REAR SUSPENSION SYSTEM: Adjustable in two positions. With brakes applied, use foot to make adjustment.
Release suspension moulding as showed in the figure for a soft option for the young infant.
7 - Press down on suspension moulding, for a strong but comfortable setting for the larger child.
8 - TO REMOVE THE REAR WHEEL: Press lever downwards and at the same time pull the wheel away from the axel
housing.
9 - TO FIT THE REAR WHEELS: Place axel in axel housing and press inwards.
Check by pulling wheel to confirm latching of the axel.
10 - TO REMOVE THE FRONT WHEEL:
button is in a upwards position.
Press button and at the same time pull the wheel away from the front leg.
11 - TO FIT THE FRONT WHEELS:
upwards position.
Press button and at the same time push wheel housing into front leg, until it locks into position.
Check by pulling wheel to confirm latching of the wheel housing.
12- ADJUSTABLE HANDLE HIGHT: Press the two buttons simultaneously and rise or lower the handle bar as required.
13 - TO FIT CARRYCOT: Place carrycot base on chassis attachment device "easylock". Lock will automatically engage.
Warning: Check that the pram body attachment devices are correctly engaged before use.
TO REMOVE CARRYCOT: Push in button on base of the carrycot and simultaneously lift carrycot away from
chassis frame.
14 - TO FIT SEAT: Seat may be forward or rear facing. Place seat on chassis attachment devise "easylock". Lock will
automatically engage.
TO REMOVE SEAT: Push in button on both side of seat unit and lift seat away from chassis frame.
15 - TO FIT AUTO SEAT: Place auto seat on chassis attachment devise "easylock". Lock will automatically engage.
Warning: Check that the auto seat attachment devices are correctly engaged before use.
TO REMOVE AUTO SEAT: Push in button on back of seat unit and lift auto seat away from chassis frame.
16 - FOLD PUSHCHAIR:
N.B: Please remember to lock the swivel wheels in the non-steering mode before folding chair.
When folding the pushchair ensure that the adjustable handle is in line with the main handle.
To fold, firstly press the red button and simultaneously, turn the handle collar in the direction of the "FOLD" and the
chair will begin to close.
17 - Operate secondary safety device by pulling the plastic tab.
Tilt the chair forward and continue the folding action until the chassis is fully closed.
18 - TO STORE PUSHCHAIR: Fold adjustable handle as shown in the figure.
19 - BASKET: To attach the basket, pass the webbing and press-stud through the frame as shown.
Attach the back edge of the basket around the rear cross member.
N.B. The front wheels of this chassis can only be removed if the steering
N.B. The front wheels of this chassis can only fitted if the steering button is in a
Warning: Check that the seat unit attachment devices are correctly engaged before use.