Operation - Makita DWT310 Betriebsanleitung

Hook
CAUTION:
Be sure to attach the shoulder belt
included in the tool as the standard accessory.
Use the shoulder belt for carrying the tool, and
never use the hook for other purposes such as
the fall prevention at high location. If the hook is
used for other purposes, excessive load may break
them and cause serious injury to the operator and
person around/underneath the operator.
CAUTION:
When you attach the shoulder
belt to the hook, be sure to attach it securely. If it
is attached incompletely, the tool may come off and
cause an injury.
CAUTION:
When carrying the tool using
the shoulder belt, be careful not to entangle the
shoulder belt with your body or objects and not to
hit objects with the tool. Failure to do so may cause
an accident.
CAUTION:
Remove the shoulder belt from
the hook before operating the tool. Failure to do
so may lose your balance at operation and cause an
accident.
► Fig.6: 1. Hook 2. Shoulder belt
Attach the shoulder belt included in the tool as the
standard accessory to the hook for carrying the tool.
Remove the shoulder belt from the hook before operat-
ing the tool.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Removing the outer and inner
sleeves
CAUTION:
Be careful not to allow foreign mat-
ter to enter the insides of the tool when removing
or installing the outer and inner sleeves.
1. Loosen the two screws while holding the outer
sleeve. The outer and inner sleeves will be pushed up
by the springs built into the tool.
► Fig.7: 1. Outer sleeve 2. Screw
2. Press the pin down to remove the inner sleeve
from the outer sleeve.
► Fig.8: 1. Inner sleeve 2. Pin 3. Outer sleeve
NOTICE:
Be careful not to drop the inner sleeve
when removing it.
NOTICE:
Do not remove the tip rod, tip rod
spring, and inner sleeve spring from the tool.
► Fig.9: 1. Tip rod 2. Tip rod spring 3. Inner sleeve
spring
Installing the outer and inner
sleeves
Place the inner sleeve with the pin facing upward.
Attach the outer sleeve to the inner sleeve securely
while pressing the pin of the inner sleeve.
► Fig.10: 1. Outer sleeve 2. Pin 3. Inner sleeve
Insert the outer and inner sleeves into the tool while
rotating the inner sleeve clockwise and counterclock-
wise until the outer sleeve touches the tool. Tighten the
two screws firmly.
► Fig.11: 1. Outer sleeve 2. Screw
NOTICE:
Make sure that there is no gap between
the outer sleeve and the tool.

OPERATION

CAUTION:
Always insert the battery cartridge
all the way until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around you.
CAUTION:
Keep the bolt tips off of the
ground, floor, walkways, etc. to prevent injury
from tripping or falling.
1. Tighten bolts preliminarily by using a hand wrench.
2. Hold the tool firmly and place the inner sleeve over the
bolt so that the inner sleeve completely covers the bolt tip.
► Fig.12: 1. Inner sleeve 2. Bolt tip
NOTICE:
Be careful when fitting the sleeve onto
the bolt tip. Striking the tip can damage it so that it
will no longer fit inside the sleeve properly.
3.
Push the tool lightly until the outer sleeve com-
pletely hold the nut. If the outer sleeve fails to hold the
nut, rotate the tool clockwise or counterclockwise while
pushing the tool lightly.
4. Press the trigger-lock button, and then pull the
switch trigger. The outer sleeve rotates to tighten the nut.
► Fig.13: 1. Outer sleeve 2. Nut
NOTICE:
Do not force the tool down excessively.
Apply the downward force to the degree needed
to stabilize the tool.
5.
When the specified torque is attained, the bolt
tip will be sheared at its notched portion. The bolt tip
remains inside the inner sleeve.
► Fig.14: 1. Notched portion 2. Bolt tip
6. Release the switch trigger and withdraw the tool in
a straight line.
► Fig.15: 1. Outer sleeve
7. Pull the eject lever to eject the bolt tip from the
tool. Catch the sheared bolt tips to prevent them from
falling.
► Fig.16: 1. Bolt tip
8 ENGLISH