Makita DTW181 Betriebsanleitung Seite 4

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
F astening c apac ities
S q uare d riv e
No load speed
I mpac ts per minute
O v erall length
R ated v oltage
Net w eigh t
• Due to our continuing program of research and development, the specifications herein are subject to change
w it h out noti c e.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est c ombination, a c c or d ing to E P T A - P ro c e d ure 0 1 / 20 1 4 , are s h o w n in t h e table.
Applicable battery cartridge and charger
Battery cartridge
C h arger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
resi d en c e.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
T h e tool is inten d e d f or f astening bolts an d nuts.
Noise
The typical A-weighted noise level determined accord-
ing to EN 6 2 8 4 1 -2-2 :
Sound pressure level (L
pA
Sound power level (L ) : 106 dB (A)
W A
Uncertainty (K) : 3 dB(A)
WARNING:
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mine d a c c or d ing to EN 6 2 8 4 1 -2-2 :
Work mode: impact tightening of fasteners of the maxi-
mum capacity of the tool
Vibration emission (a ) : 10.5 m/s
h
Uncertainty (K) : 1.5 m/s
S tand ard bolt
H igh tensile bolt
H ard impac t mod e
S of t impac t mod e
H ard impac t mod e
S of t impac t mod e
) : 95 dB(A)
2
2
BL 1 8 1 5 N / BL 1 8 20 / BL 1 8 20B / BL 1 8 30 / BL 1 8 30B / BL 1 8 4 0 /
BL 1 8 4 0B / BL 1 8 5 0 / BL 1 8 5 0B / BL 1 8 6 0B
D C 1 8 R C / D C 1 8 R D / D C 1 8 R E / D C 1 8 S D / D C 1 8 S E / D C 1 8 S F
NOTE: T h e d e c lare d v ibration emission v alue h as
been measure d in a c c or d an c e w it h t h e stan d ar d test
method and may be used for comparing one tool with
anot h er.
NOTE: T h e d e c lare d v ibration emission v alue
may also be used in a preliminary assessment of
exposure.
WARNING:
T h e v ibration emission d uring a c tual
use o f t h e po w er tool c an d i f f er f rom t h e d e c lare d
emission value depending on the ways in which the
tool is use d .
Be sure to identify safety measures
WARNING:
to prote c t t h e operator t h at are base d on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
t h e times w h en t h e tool is s w it c h e d o f f an d w h en it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to t h is instru c tion manual.
4 ENGLISH
DTW181
M8 - M1 6
M6 - M1 2
1 2.7 mm
-1
0 - 2,4 00 min
-1
0 - 1 ,300 min
-1
0 - 3,6 00 min
-1
0 - 2,000 min
1 5 1 mm
D .C . 1 8 V
1 .2 - 1 .5 kg