Inhaltsverzeichnis
Werbung
• Only use an extension cord which is intended for out-
English
door use and equipped with a splashproof coupling-
socket
Angle grinder
BEFORE USE
• Before using the tool for the fi rst time, it is
INTENDED USE
recommended to receive practical information
This tool is intended for grinding, cutting and deburring
• Do not work materials containing asbestos (asbestos is
metal and stone materials without the use of water; with
considered carcinogenic)
the appropriate accessories the tool can also be used for
• Take protective measures when during work dust can
brushing and sanding
develop that is harmful to one's health, combustible or
explosive (some dusts are considered carcinogenic);
TECHNICAL SPECIFICATIONS
1
wear a dust mask and work with dust/chip extraction
when connectable
2
• Be careful of hidden electrical wires or gas- and water
PRODUCT ELEMENTS
pipes; check the work area, for instance with a metal
detector
1. Spindle
• Be careful when cutting grooves, especially in support-
2. Clamping fl ange
ing walls (slots in supporting walls are subject to coun-
3. Spanner
try- specifi c regulations; these regulations are to be ob-
4. Spindle-lock button
served under all circumstances)
5. Auxiliary handle
• Clamp the workpiece in case it does not remain stationa-
6. Safety guard
ry from its own weight
7. Mounting fl ange
• Do not clamp the tool in a vice
8. On/off locking switch
• Use completely unrolled and safe extension cords with
9. Switch locking knob
a capacity of 16 Amps (UK 13 Amps)
• Wear protective glasses and gloves, hearing protection
SAFETY
and sturdy shoes; when necessary, also wear an apron
WARNING! Read all instructions. Failure to follow all in-
• Always mount auxiliary handle (5) and protective guard
structions listed below may result in electric shock, fi re
(6); never use the tool without them
and/or serious injury.
• Be sure tool is switched off when plugging in
• Only use this tool for dry grinding/cutting
DURING USE
• Only use the fl anges which are supplied with this tool
• Always keep the cord away from moving parts of the
• This tool should not be used by people under the age of
tool; direct the cord to the rear, away from the tool
16 years
• If the cord is damaged or cut through while working, do
• Always disconnect plug from power source before
not touch the cord, but immediately disconnect the plug;
making any adjustment or changing any accessory
never use the tool with a damaged cord
• Push spindle-lock button (4) only when spindle (1) is at
ACCESSORIES
a standstill
• Use the original SBM Group accessories which can be
• Keep hands away from rotating accessories
obtained from your SBM Group dealer
• When grinding metal, sparks are generated; keep other
• For mounting/using non- SBM Group accessories ob-
persons and combustible material from work area
serve the instructions of the manufacturer concerned
• In case of electrical or mechanical malfunction, immedi-
• Use only accessories with an allowable speed matching
ately switch off the tool and disconnect the plug
at least the highest no-load speed of the tool
• In case the cutting disc is blocked, resulting in jerking
• Do not use damaged, deformed or vibrating grinding/
forces on the tool, immediately switch off the tool
cutting discs
• In case of current interruption or when the plug is ac-
• Handle and store grinding/cutting discs carefully to
cidentally pulled out, unlock the on/off switch (8) imme-
avoid chipping and cracking
diately and put it in the OFF-position in order to prevent
• Protect accessories from impact, shock and grease
uncontrolled restarting
• Do not use a grinding/cutting disc that is larger than the
• Do not apply so much pressure on the tool that it comes
maximum recommended size
to a standstill
• Only use grinding/cutting discs with a hole diameter
which fi ts mounting fl ange (7) without play; never use
AFTER USE
reducers or adaptors to fi t large-hole grinding/cutting
• Before you put down the tool, switch off the motor and
discs
ensure that all moving parts have come to a complete
• Never use grinding/cutting discs with a threaded hole,
standstill
of which the thread is not long enough to accept the
• After switching off the tool, never stop the rotation of the
spindle length of the tool
accessory by a lateral force applied against it
• Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
OUTDOOR USE
in the cord of this tool to the earth terminal of the plug
• Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
6
Werbung
Inhaltsverzeichnis
