SSS Siedle AHT 870-0 Produktinformation Seite 7

SD-Karte
Auf der Geräteoberseite ist eine
Blind­Karte als Staubschutz in einen
SD­Karten­Slot eingesteckt. Bei einer
nachträglichen Funktionserweiterung
kann hier eine Speicherkarte einge-
baut werden.
Zubehör für AZTV 870-...
AZTV 870-... Zubehör-Tisch für
die Umrüstung von Wandgerät zu
Tischgerät.
Lizenzen
Durch Zukauf einer Access Lizenz-
Upgrade Video „ALUV 270-..."
können Sie nachträglich bei einem
Audiogerät AHT/AHF 870-... die
Videofunktion frei schalten.
Technische Daten
Versorgung des Gerätes über PoE
(Klasse 2)
Klingellautstärke: max. 83 dB (A)
Farbdisplay: 8,8 cm
Auflösung: 320 x 240 Pixel
Eingang für Etagenruf ERT
(potentialfrei)
Potentialfreier Kontakt:
max. 30 V, 1 A
Abmessungen (mm) B x H x T:
105 x 277 x 45
English
Application
Access in-house telephone with door
release button and 7 additional but-
tons with 2-colour status LED. All
buttons are freely programmable.
The display shows the graphic menu
interface, but not a camera image.
It is possible to upgrade to a fully
functional video station.
With the functions calling, speech,
door release, vision, light, remote
switching and call silencing.
With the additional purchase of
licence ALUV 270-..., the
AHT 870-... can be converted into a
fully functional indoor video device.
Performance features:
• Display 8.8 cm
• Call differentiation between door
calls, storey calls, indoor calls and
concierge calls
• Switching functions
• Status indications
• Can be used with table­top acces-
sory AZTV 870-... as a table-top
device
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of delivery
• AHT 870-... (Base plate and
housing with circuit board)
• Receiver
• No-tangle cord
• Two RJ45 plugs
• Dummy card for SD card insert
• Operating instructions for the
end user
• This product information
Mounting
1 Recommended mounting height
appr. 1.65 m to display height/
viewing height.
2 Open the device from the back
by releasing the base plate with the
locking lever.
3 Align the base plate centrally rela-
tive to the flush mounted socket and
mark the fixing holes.
4 Insert the provided RJ45 plug on
the adapter circuit board. Fasten
the base plate directly on the wall
using 4 screws, paying attention that
the plate is the right way up (top
marking).
5 Insert the coloured plug of the
no-tangle cord into the socket at the
housing. A distinct click is audible
when the plug is correctly inserted.
6 Insert the other end of the no-
tangle cord in the receiver until
the plug clicks audibly into place.
This connection can no longer be
detached.
7 Hook the housing into the base
plate from above and close by
exerting a slight pressure.
Dismantling
8 To remove the housing, press
the lock upwards using a flat blade
screwdriver. The circuit board and
receiver remain on the upper part of
the housing.
Lettering
9 The lettering panel can be
inscribed to indicate the button
functions. The see-through panel
can be lifted at the side.
A marking template is provided in
the download area of our website.
3